Environment
SoC: nRF54LM20A (cpuapp, non-secure / TF-M)
nRF Connect SDK: v3.3.0
sQSPI soft peripheral driving an AMOLED display via the FLPR
BLE active via MPSL...
Hi,
We had connectivity issues on our end for the Message Routing Service webhook since May 13, 2026. It has been restored and tested with the nRF Cloud verification test...
Hi,
I see the different behavior of the function sd_ble_gap_conn_param_update when connected to Windows integrated Bluetooth.
Using bare-metal SDK v0.9.0 it succeeds...
Hello Team,
We are evaluating an architecture where an NXP MIMXRT700 EVK powers an nRF9151 DK externally while using the nRF9151 DK as an LTE modem.
Hardware:
MIMXRT700...
Hello, We have registered our project with Nordic. Our project ID is 60803622472. Project title: DECT NR+ Star Topology Sensor Node Evaluation with nRF9151 We would like to...
Hello,
Quick one:
https://docs.nordicsemi.com/r/bundle/nordic-mcp/page/index.html seems to be broken. I have a myNordic account and everything. I tried on two different...
Hi all. I am testing the NPM1300 with nrf54l15 using vallina Zephyr. I've setup device tree for npm1300 to generate interrupt on its GPIO0 when there is event.
When Vbus...
Is it possible to get to port of an UDP socket (ephemeral, offloaded to modem) with NCS 2.9.0 and mfw 2.0.2?
I tried "getsockname" and get "errno 95 (Operation not supported...
Dear Nordic Team,
I am participating in the Board Designer Competition sponsored by Nordic Semiconductor and Autodesk Fusion 360. My project has been selected for free hardware...
Hi,
I am trying to build a BLE PAwR network jammer for wireless network hardening. I have three nrf52840 transmitting on channels 37,38 and 39, which blocks nodes from joining...
I'd like to update a firmware which is essentially made of 2 parts, say 0x1000-0x8000 is a "read-only" part and 0x8000-0x50000 is a "read-write" part. If I flash this firmware...
Hi Nordic Team,
Is there any way to input 3 audio streams (through I2S ) on nRF5340DK board are there any extra I2S Port available to input one more sinusoidal signal and...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
I want...
Hi, I'm following the Academy lessons and just tried to get the Blinky sample to work with a nRF54L15DK. I can see on a serial terminal that the code is running and console...
Running the WiFi scan sample on a Thingy91X or NRF7002DK in SDK 2.8 and 2.9 works for scan_done results but if you change to show raw scans, no raw scans are displayed. The...
Hi Support Team
The VDD of customer’s nRF54L15 board is 3V, but the high voltage of P1.10 is about 1V. Did you meet this issue before? Customer needs the output high voltage...
Dear Nordic Team,
I am currently working on a project that integrates your HTTPS client sample with your BLE provisioning sample, specifically on the nRF5340 with the 7002EK...
Hi,
I am testing the Bluetooth remote discovery of the nRF52840 in LE Coded mode with the transmission power set to 8 dBm.
The farthest distance currently achievable is...
Hello, I have developed a module using 54L15 and am currently measuring its RF performance. On Rohde & Schwarz instruments, I have observed numerous test results regarding...
Hello.
I am trying to follow Downgrade protection using MCUboot to enable Hardware-based downgrade protection. However, an error occurred, and the software did not start...
I used the battery routine to test the ADC, and the voltage measured was 3 times larger.
How to fix this problem？
Bat+ is 3.3 V.
dts setting:
vbatt {
compatible...
