Product: nRF54L15DK, SDK V2.9.0
Application: Multi protocol (BLE + Matter/Thread) Door Lock
Issue: BLE bonding is not retained after power cycles. The mobile app requests...
I successfully am using BLACK MAGIC PROBE (BMP) with nRF Connect Extension in VScode already, based on answers in this support forum. I can Run, Pause, Examine breakpoints...
I found this pretty old post devzone.nordicsemi.com/.../switching-between-apps-with-dual-bank . Currently I am building two different zephyr projects and selecting between...
Hi,
we have ESB PTX and PRX couple from nRF54H20 nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect plugin build for CPURAD...
We are currently developing a project using the nRF52832 as the microcontroller, Segger Embedded Studio version 5.42a as the IDE, and the nRF5 SDK 17.0.2. We began by creating...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
Hello,
My name is Mehdi, and I am a student in a french university. Actually, I am working on a project and I aim to use the Heart Rate for a statical studies to use it...
Hi,
I'm trying to use the NRF24L01 as a replacement to HS6200p. But I can't find 0x1E (SETUP VALUE) and 0x1F (PRE_GURD) in the NRF24L01 datasheet. Actually, in the datasheet...
Hi everyone,
I am using the following:
*nRF51422
*SDK11
*keil uVision 5.17
*s130
I have been working with nRF51 that scans beacons and stores it into persistent...
Hello everyone,
I am trying to set the security parameters for bonding with PASSKEY (static)format it is getting executed very well(connected and bonded) for the SDK 9...
Dear all:
My device uses LDO mode and DC-DC mode respectively, and the distance is different.In 4dbm, the distance of the LDO mode is 110m, while the LDO mode is in the 70m...
Hi,
I was wondering if anyone could clarify why there are enable, set and clear (CHEN, CHENSET, CHENCLR) for the PPI channels when according to the data sheet they all...
I checked S130 document for using nRF51822.
I want to change the nRF51822 like the following mode.
peripheral => central => scanning => peripheral => central => scanning...
Hello
I am trying to change the ticks value of Battery measurement interval (ble_app-prox example) but i am not able to understand how the ticks period is measured based...
Hi,
I was seeing memory leak issues when using NRF51 with JLkink v4.98. See this link:
forum.segger.com/index.php
This issue has been fixed with the latest version of...
The address miss event is not shown as a transition in Figure 22 of the NRF51 Reference Manual. What state does the NRF51 enter upon an address miss and how long after the...
To use BEL application, the soft device must be downloaded before programming.
i can find a table shows that which soft device version is suitable for chip version.
how...
Our application is developing RC units for small (indoor) model airplanes - we want to be able to have multiple planes flying at once without "stepping" on each other.
...
I'm developing a NUS-based peripheral and adding a timeout to force a disconnect after a period of inactivity (i.e. no incoming NUS data). However my peripheral also provides...
Hi all,
I'm trying to use Ant+ HRM RX demo profile from nRF51_SDK_10 ( nRF51422 ) between my board PCA10028 and a Garmin rate sensor but I get some trouble.
Let me explain...
