Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hello
I'm using nrf51822 EK board. This is my first time to develop application in ARM system.
I want to develop a ble application.
This application can be shut down (system...
I've got my custom PCB design assembled. Attached segger jlink, but it detects only 0.1 V, although Vdd is 3V.
How is the power measured?
What should I read on SWDIO...
Dear
Is there a possibility within Nordic SoC to make a passive RFID Tag which will connect to SmartPhone via Bluetooth?
Just like µBlue Series, but smaller and using...
I found the "S110_SoftDevice_Specification_v1.2.pdf" but not the "S110 softdevice release notes" mentioned in a previous question about DCDC usage. Where is that doc?
What...
I have been developing on a nrF51422 QFAAC0 chipset. That chipset required SDK 4.4 for soft device capability.
I requested the latest silicon (so I could develop against...
Hello,
I would like to build a tool in Python that allows sniffing/interaction with BLE traffic between nRFgo modules (nRF51822) and a Mac via the master emulator. I am...
I have bought the Bluetooth low energy evaluation kit nRF51822. It can be paired with a Nexus and a Sony Xperia without problems, but it does not appear at all on Samsung...
L.S.
Today I decided to have a look at SDK5.1.0 for nRF51822 which supports the S120.
It is deliverd as an msi file with (as far as I have noticed) no support for specifying...
Is there anything preventing anyone from uploading the tinyest image that simply dumps the entire ROM content on the UART?
This would sort of circumvent the HW locking...
Hello,
I use nRF51822 for my project and I would like to purchase some BLE packet sniffer. Does anyone recommend any sniffer? My purpose for that is debugging and check transaction...
On PCB layouts I often see that the HF xtal is oriented at 45 degrees relative to the orientation of the 51x chip (that is to say the edges of the the xtal and 51x chips are...
Hello Nordic expert,
Regarding the antenna load impedance, I can find the data in nRF24L01+ datasheet and it is 15ohm +j88ohm.
But I can not find the antenna load impedance...
hi,
now ,i have save the power,so need to close the spi interface at some time.
but when i call follow function (hal_spi_disable).
it see not close the spi interface, ...
Hello,
During programming bootloader provided with sdk
I get some messages in Command window in Keil.
Load "C:\Keil\ARM\Device\Nordic\nrf51822\Board\nrf6310\device_firmware_updates...
Since I'm writing code for my own board, I decided to create my own board.h file to hold the board-specific definitions.
However, I can't do this without hacking the SDK...
