Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hello everyone,
I am designing a Bluetooth repeater that will be powered eather by USB or an embedded Li-Po battery. This device will run with the nRF52833 along with...
Hi,
I am working on a project, where I am trying to create a touch LED project using NRF52832. I have completed the prototype, its working is quite simple. The LED will...
Hello, guys!
We are using nRF51822 SoC with nRF5 SDK v12.3.0 and s130 SoftDevice. One of our desires is to use Software Interrupt (SWI) driver.
However, when I try to...
Hello all,
I am configuring a low power application for the nrf52832 board (custom board). This is a very low power application and I want the board to stay on sleep mode...
Hello everyone, I am working with a BMI160 6-DoF sensor. I have some drivers related to this chip. Using the Segger J-Link debugger the drivers just work fine without any...
I update a couple of device to mfw_nrf9160_1.3.2.zip.
Before that (1.3.1), my experience was to get a ENETDOWN, when calling " sendto" while the device has lost some the...
Hi.
I'm trying to add Bluetooth capability to the "Asset Tracker V2" project. I was able to do it on the nRF9160DK board. I could not find a working example to make the...
Hello,
windows10 x64.
i have used NCS1.9.1 and NCS1.9.99,now i want update to 2.0.99
how to install NCS2.0.99?
because nRF Connect for Desktop Toolchain manager no...
Hi,
1. How to calculate the Flash and RAM usages at runtime? I am able to do it static way but wanted to analyze this at runtime.
2. How to calculate the Heap usages at...
Hallo,
currently I try to optimise the functionality of my extended advertiser code. I found that there are also some call-backs defined for extended advertisers. The struct...
I use iOS nRF Connect APP to test DFU. But it failed with writing is not permitted.
The following is log message of nRF52832 device. 00> <info> app: Inside main 00> 00>...
Hi,
I am working on a system that runs a proprietary protocol, i.e. non-BLE, which works fine when it uses either uncoded links or S=8 ( LR125Kbit ) coded links, but I want...
Hello everyone, I am trying to send a string printed float number using the ESB protocol. I am using nrfConnect SDK 1.9.1 with nrf52832, started off with the supplied esb_ptx...
Respected,
I am using NRF connect for desktop for programming my actinius sensor (ICARUS IOT BOARD) but whenever I want to upload and reset the board using actinius programmer...
