Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
We are working on a project using the nRF5340 with SDK version 2.4.2. We have integrated a NAND flash using standard SPI communication, utilizing the QSPI-assigned pins...
Hello
I am planning to design a custom board for my battery operated application and for that I need 5GHz Wi-Fi, Ultra lower camera. I need suggestions which camera is...
Hello,
I am currently working on a mesh sensor system. I have got one sensor board and one board for connecting in the mesh system. Now I want to be able to send the sensor...
Hi：
My environment is: nRF5_SDK_17.1.0_ddde560, keil, s113_nrf52_7.2.0_softdevice
When using usbd_cdc, I found that DTR must be set to start communication. Is there any...
Hi,
i develop my product ny ncs V2.6.0. in some case,i need store some user data to the flash，but i dont know how to read and write flash in cns sdk.if there is some samples...
Greetings.
Our team has encountered some difficulties in integrating nPM1300 into a new project. In the project we plan to use nPM1300 in conjunction with NRF52810. To develop...
* The nPM1300 LDSWSTATUS register @ Address offset: 0x4 doesn't contain values in the "Value" column.
* ID "E" occupies only one bit, but declares data on 4 devices:
...
Hi, I try to launch west build command from a terminal.
I am first generating environnement variable as stated in this post :
Then I call it, and finally, I launch this...
Hello,
I am working on a custom board designed around the NRF52840. Currently the bootloader on the board is the same as the one on the NRF52840 DONGLE. It is out intentions...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
My goal is to achieve a data throughput...
We are connecting nrf boards to solar charged batteries for power consumption. We will be remotely deploying the boards on field. The boards are connected to sensors, from...
I'm going from v2.6.1 to v2.7.0; I'm using a thingy53. I'm getting a voltage error prior to boot.
[00:00:00.002,929] <err> voltage: setup: -134 *** Booting nRF Connect SDK...
Hi,
I evaluate MCUBOOT and trying to understand how it works. I am using a nRF52840DK. I have base my demo on this course ( Exercise 1 - DFU over UART - Nordic Developer...
Hi,
We would like to disable all wakeup sources before calling sys_poweroff. How to achieve this using Zephyr API? Pin configuration should remain as previously configured...
