Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hi,
I am using nRF7002 DK. I have set P1.04 as UART RX. For testing I am using TI CC26x2R1 Launchpad to send UART data to nRF7002 DK. I use a logic level shifter board to...
Hello,
I am currently trying to connect an external hardware codec and amp (Adafruit MAX98357 I2S Class-D Mono Amp) in order to play audio via BLE Audio and I2S using...
I have an NRF9161DK 1.0.0 , I was trying to do some wiring but the sensors didn't work, then I noticed that the board delivered 1.7v.
I tried changing it to 3.3v using the...
Hi,
My NRF52840DK ( pca10056 1.1.0 2019.9) would not reset when I press its Reset button. The issue is very similar to https://devzone.nordicsemi.com/f/nordic-q-a/38555...
I have new Thingy 53. Default Edge Inpulse demo works without any problem. But I have problem with Weather Station demo.
First I tested Zigbee version. After flashing using...
Hi,
What is the minimum LDO dropout voltage of nPM1300? For instance, in order to get 3.3V from the LDO, what is the minimum input for the LDO ? On the datasheet there is...
Dear all:
I have prepare env for border router successfully following this link( developer.nordicsemi.com/.../tools.html , Raspberry Pi4 and nRF52840( RCP: radio coprocessor...
I have a customer that wants to provide me with .a file for some confidential algorithm they want to run. I am tasked with implementing this into my firmware.
Using the...
I can't seem to get the FIFO to work and I think it is because I'm not dereferencing the consumer thread properly. I have reviewed the nRF Connect SDK Intermediate, data passing...
Hi,all
I need to connect BLE via NFC,but I do not know which example should i use to start。and i am a new field of NFC ,is there some document about NFC?thank you a lot...
https://devzone.nordicsemi.com/f/nordic-q-a/44658/communication-probl
I want to change the code provided in this link to enter the password from the peripheral
Hello,
I am using nRF Connect 2.5.2 with a Xiao Seeed BLE Sense nRF52840 and Jlink EDU mini
I am trying to flash the peripheral_hids_keyboard sample with Ozone, and I...
Hi everyone,
I'm trying to measure battery level using nRF52833. Reading previous posts, there are two popular ways to measure battery level with SAADC module 1) battery...
Dear All,
I need your help to clarify some LE Audio protocol related concepts.
For the BIS use cases. When the PC pause the playback, after that, are there any ISO packets...
