Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
can i ask how do i send sensor readings from BME280 , SGP40 & SHT40 to nRF cloud. i has installed nRF Cloud gateway app ( Android) but it keep loading. So i am asking...
We are working with a custom nRF52840 PCB and would like guidance on the correct and supported way to build a firmware equivalent to the radio_test sample on the nRF52840...
I am working with nRF54L15 running Thread CLI . The device is successfully commissioned to a Thread network and communicates through a Border Router (BR) . SDK version V3...
I am implementing the production line frequency trimming step for the nRF7002, as per https://docs.nordicsemi.com/bundle/nan_043/page/APP/nan_043/xtalxo_freq_trimming.html...
Hello,
Is there any documentation on setting up VoIP on the nRF91x module with Zephyr?
As the nRF91x does not have a built-in VoIP app layer, I can assemble the hardware...
I have downloaded the nrf SDK v3.2.1 and i am testing its BLE sounding reflector and initiator sample code on two different xiao boards here is what i am getting at the serial...
I am using an nRF52840 DK (Version: 3.0.1). After a failed update/event, the DK is no longer recognized by my OS (Windows) via USB. LED5 blinks once when the usb is connected...
Hi:
Hardware setup: nRF52840DK interfacing with Adafruit LIS3DH (ST LIS3DH) over I2C on pins P1.14 and P1.15
Software: ncs-v3.2.1, Zephyr 4.2.99
Kconfig: I2C bus drivers...
I have a question regarding the nRF5340. I would like to capture and access the raw payload of BLE packets that fail the CRC check.
I know that with the nRF52840 (running...
I have a few doubts regarding power macros and getting the result I want. From combing through posts I have found the following: Since BT840XE has a FEM, you need to properly...
Hello Team,
Working on nrf54l15 using NCS SDK version 3.0.2 and tool chain version 3.0.2 Currently facing error while build. Following is the error
CMake Error at cmake...
We have engineers with newer android devices unable to install the nRF Mesh Sniffer app on newer android devices. The Google Play store says "not available for any of your...
Hi, I am working on a channel sounding positioning system using one initiator and 7 reflectors. Since concurrent channel sounding does not work, the program performs sequential...
Hi, I took my old NRF52840 DK PCA10056 revision 2.0.1 and tried evaluating it today after few years. I am unable to connect to the target. I have 2 identical boards that were...
Hi ,
We have a device running nRF5 SDK 16.0.0 with SoftDevice S332 (BLE + ANT). We use BLE Central/Peripheral links plus multiple ANT sensors. Under load we see frequent...
