Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
We are trying to send a large message via a BLE characteristic and to do that we have broken up the message payload into smaller fragments and calling bt_gatt_notify() repeatedly...
hi：
I use ble_app_uart routine, test the receiving rate, use the mobile phone to send data, 52832 receive the fastest can only be 10KB.
In addition, when the interval...
Hi
Compile the cli sample into a hex file,Download it to the board, read the hex file through the nRF Connect for Desktop Programmer tool, and then convert it to the bin...
Description:
Facing an issue with k_sleep() function misbehaving after few months due to the internal counter ticks crossed uint32_max values. Simulated the same by hardcoding...
Hi,
we are currently using NCS 2.0.2 on nRF52840 .
Is it possible to disable uart1 via pinctrl or another library during runtime and re-configure the rx/tx as gpios? ...
Hi,
I have met some problems while building the environment of pc-ble-driver-py. Error occurs in this command. The error points that I do not install git, but I have installed...
Hi, I'm new to nrf development. I was able to successfully install the SDK and toolchain using the toolchain manager. But when I'm trying to build a sample project "Blinky...
Target: nrf52 dev kit
Soft device: s132_nrf52_7.2.0_softdevice.hex
SDK: nrf5 sdk 17.1.0
Environment: IAR
Example modified: ble_app_rscs I am trying to modify the example...
Hello,
I am currently developing an LTE/LwM2M application on a custom board using the nRF9160 and NCS version 2.1.0. The application is almost finished and works great,...
Hi team,
We are using NRF52833 with PCA10100 on it and soft device version is s140.
We are advertising with both service data and manufacturing data.
1. Initially when...
There are two UART interfaces in nRF52840:
We have refer to nRF52840 and nRF52840 DK materials, but we found only one UART connection reference.
We want to know how to...
Hello, team.
I have some questions about reset restriction of nrf9160.
Q1. Does the restriction timer(30minutes) still run after +CFUN=0?
Q2. What is the exact meaning...
Hi guys. I read this thread answered by Einar Thorsrud. devzone.nordicsemi.com/.../direct-advertising-example
"HID mouse example uses direct advertising, but only when it...
I am using nRF52840 dongle with raspberry pi 4 to create a thread network. I downloaded nRFconnect for desktop to flash the hex files into the dongles.
I successfully flashed...
