Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello,
I am working on an application (peripheral device) where a connection interval of 11.25ms with the central is essential. The desired behaviour is that if the central...
For the nRF52832 is it able to send out information to another device such as an app. I am aware that this device can be implemented on an electronical device however my intended...
According nrfxlib - modem library - supported features , the nRF9160 firmware supports:
DTLS 1.2 client
TLS 1.2 client
My experience with the TLS client...
Hello,
we have an existing product in "peripheral" role, based on the NRF52832 and soft device S132.
We plan to add support for multi link operation, so that the peripheral...
HI
An example of zigbee multi-sensor is to use log enable info zigbee.report to enable log display. Is there any more information that can be turned on and displayed in...
Hey there! I'm very new to BLE, so I wanted to reach out in this forum to confirm hardware capabilities before I purchase any devices. I'm currently looking at the nRF52840...
hi team,
i am using nrf52840 controller,in my project along with with nrf_sdk.
i wrote a led blicking code using ble protocal on segger IDE 5.40 and i want to see data...
Hi, I'm using nRF52840 in my project. I successfully integrated the BLE DFU service and its characteristics in my firmware, Now I can update the firmware through the nrf-connect...
Hi, we are doing mass production using PLT. And we have found that like 10% of the sensors are stuck in certain stage as seen in following power cycle images.
The program...
Hi,
In the product specification document of nRF52840 it says that in order to read the counter register's value I need to set the capture task NRF_TIMER1->TASKS_CAPTURE...
Hello,
I would like to use the UICR customer registers to store our devices serial numbers.
Can you please point me to some example code for nRF52833 SoC.
I am using...
Hallo Team,
I would like to operate nrf5340 BLE module (BC40C from Fanstel) in "Normal Voltage Mode". Please find the screenshot of the module below. I hope its clear...
Hi,
Just wondering if it's possible, or there is a reliable way to dynamically change the sampling period of the CAF sensor manager module . Specifically the values defined...
Hi everyone!
I am using ESB with the nRF5340dk without ACK, but from time to time need to send a packet with an ACK request in order to send some commands from the receiver...
