I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi! I'm using nrf52832 and SDK 16. I have a custom board that doesn't have an external oscillator for low frequency clock and uses internal RC so pins 0 and 1 can be used...
I am using RTT logging and it is interfering with USB HID data transfer. The host sends consecutive OUT packets and I print some logs after each one. I will miss a APP_USBD_HID_USER_EVT_OUT_REPORT_READY...
Hi,
We are using nRF52840 chipset with SDK 15.0.0 with Mesh implemetation.
1. We are provisioning the mesh node using the nRF mesh APP.
2. Then we are resetting the...
Hello,
I had been looking at BLE mesh documentation as well as the examples on the SDK and looks every node should have a dedicated function. generic on/off server controlling...
Hello!
I am trying to interface with some old hardware that communicates over a single data pin. I need to take in varying 32-bit packets and output the data that translates...
Hi all,
The chip we used is nRf52832, the version of SDK I used is nRF5_SDK_15.2.0_9412b96.
The problem is when I pair to windows 10, sometimes PM_EVT_PEER_DATA_UPDATE_SUCCEEDED...
Hi,
I am using i2c driver available with zephr as i2c master. This is working fine.
I want to change the pins to P0.02 for SCL and P0.03 for SDA. I see multiple questions...
Hello,
I am looking into the peer manager and the LESC module and have some question regarding what is possible to do with this.
Is it possible to manage the private...
Hi,
I am updating SDK version from 15.0 to 17. We are using nrf52840.
I would like to know if these are necessary to add, as they were added in some examples, and if so...
Hi,
i have a problem when using the ble_uart connected to Raspberry-pie withe Bluez.
after 40 seconds the connection is lost.
tried to use several examples, but most...
Hello Community I am starter in nrf51822 i want to know if anybody has code for interfacing with ADS1115 since i didn't got any of the post which would be helpful, please...
Hello,
Is there a particular test Nordic recommends to screen for latent failures in the BLE circuit? If one has access to an Anritsu MT8852B tester with Direct-Test-Mode...
Hi,
I am updating SDK version from 15.0 to 17.0.
In many examples PM_FLASH_BUFFERS was changed from 2 to 4? What is the meaning of this change? We have one peer always...
