Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
Hi to all,
i am developing a project based on PCA10056 dev board and i want use bluetooth and NFC in sametime. separately both of them work fine but when i want use them...
Hello everyone, I am planning to use the nrf52840 with the Fingerprint module (https://www.amazon.in/dp/B07DL2DXJX/ref=cm_sw_r_wa_apa_i_Z.VlCbXSSYVRS ). The sensor interfaces...
I got a new nRF51-DK board. I was planning on using USB to program it.
On the board I see pca10028 sticker. What is this?
Also in the SDK I see pca10028, and other pca...
Im getting this error, but i thing this has to do with some python dependencies, Im getting errors with
pip3 install --user -r zephyr/scripts/requirements.txt and installing...
Hi, I have a defined MACRO which I initialised the values of ble_gap_adv_params_t in main.c. I will pass this to the function to start advertising. I used the example (ble_app_blinky_pca10056_s140...
Currently in memory map nRF5 SDK 15.2 (which apparently is a base for Thread SDK) says for nrf52840:
Bootloader settings
0x000F F000 - 0x0010 0000 (4 kB)
MBR...
The nrfx api includes nrfx_gpiote_in_event_disable/enable , but I haven't found an equivalent of nrf_gpiote_int_is_enabled for a pin. I'm attempting to port an interrupt mutex...
nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_blinky
nrf_gpio_cfg_output(16); nrf_gpio_pin_set(16);
Set P0.16 to high level under the main part of...
There seems to be little documentation on TASKS_SUSPEND and TASKS_RESUME in the SPIM with Easy DMA section of the nRF52832 data sheet. My assumption is that TASKS_SUSPEND...
Hi All,
I am working on ISP1507 which is based on NRF52832. My IDE is Keil V5.26.2.0. I have had the following problem in the UART example (pca10040e) from SDK 15.0.0. I...
Hi,
I have modified the multilink example to work with NUS and connect to 2 peripherals, but I'm facing issues with data transmission. I suspect really low throughput...
Hi
I'm testing the range of a custom sensor (nRF52840) by monitoring the RSSI. I use two receivers (the custom sensor and a nRF840 DK) and monitor the received advertising...
Hello All,
I'm very new to Nordic.
For our product development we are using NRF52832 chip and nRF5_SDK_14.2.0_17b948a stack.
Battery powered device it's so is there...
Hi,
Previously, I have done a board and this board have completely no problem to debug in Segger embedded studio.
I have route a new board, this board is almost everything...
Hi,
During evaluation of both nRF52840 Dev Kit and Dongle somehow the Dev Kit bootloader was erased. We were able to flash MCU firmware, but now J-Link is not able to connect...
