Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
It was working a few times, then suddenly I started to get these errors, which I only got previously when not running as root (perhaps because it did not have permission to...
Hi,
I am trying to process data from MPU9250 in MATLAB and I have converted " .mat " file to " .hex " file using Embedded Coder . Can someone tell me if that " .hex " file...
(1) I am using GNU C++ to develop my application with nRF5 SDK. I found the STATIC_ASSERT_SIMPLE and STATIC_ASSERT_MSG macros defined in app_util.h are not working with C...
When running the light_switch_provisioner example built on my machine, it crashes on an assert in entry_validation() in mesh_config.c:
app_error_weak.c, 95, Mesh assert...
Hi,
I've a Raspberry Pi, Node-RED, with a Thingy connected. I get a message payload, looking like this:
{"uuid":"dfb561bb7d69","characteristics":{"2a00":[84,104,105...
Dear Nordic experts,
While investigating some of my bugs, I had to look into the GPIOTE driver code, and I realized that it has some allocator for mapping GPIOTE channels...
Several answers from Nordic employees state the possibility of Secure Boot and a "Root of Trust" feature:
use of ARM TrustZone on nrf52840 for secure storage/trusted region...
Hi,
I'm studying the example code of "ble_app_blinky_pca10040_s132 ".
What confused me is I couldn't find how the "led_write_handler" is added to the service. There is...
The board is made with the nRF52832 chip and can not be scanned during the test. Could you tell me why? The nRF52 DK board functioned normally. The platform used a mesh light...
Hello, Is there any library of LSM6DS3 sensor and BMI160 sensor for NRF52832.
I am in need of Accelerometer sensor data for one part of my project.
I need to develop immediately...
Hi
i have installed nrfgo studio version (1.21.2.10)on windows 7 and 10 . Development board is listed in win7 but not in 10 it shows boards are not connected .Please help...
Hi, I try to map the UART pins RxD to P0.08 and TxD to P0.06 like on the nRF52840 PDK.
In code I have to assign a number. At the moment RX_PIN_NUMBER is 8 and TX_PIN_NUMBER...
