Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I am programming now nrf52810 I try to merge uart functionality to ble_app_blinky project but it does not work i debug and found out uar_error_handler() never been reached...
Hi.
I am using a custom board on the nRF52820 microcontroller (wiring diagram in the figure). When the microcontroller is powered only from the battery (via external LDO...
Document: HTTPS_SAMPLE_2024_09_19T02_55_15_089Z.txt I was programming the HTTPS sample with default parameters. I managed to connect to "example.com successfully". I managed...
I'm working on a BLE project based off of the peripheral_lbs sample within the nRF Connect SDK v2.7.0. I am attempting to increase the BLE security level up to either level...
Hi,
I am working on a battery powered device that collects data, save it to files and go to sleep, when it is not connected to a laptop via USB. When connected, the device...
Hi,
I want to change the LED pin that blinks to indicate BLE advertisement to pin 6. I have changed the LED_1 and LED_STOP in pca10040.h to 6:
I have also set NRF_LOG_BACKEND_UART_ENABLED...
Hi.
I am developing a custom board using nRF52840 inside a Moko MK08A and an accelerometer LIS2DH.
My circuit has a 3V3 voltage regulator just for the LIS. The microcontroller...
Hello
I'm trying to connect muy Power Profiler Kit II to my PC, and when I choose the device from the list it pops-up:
I clicked 'Program' and after I supposed it...
Hello,
I'm trying to access active PCO from nrf9160 applicaton to be able to diagnose problems like missing DNS, wrong access point etc. I tried using %XPCO command, AT...
Hello.
I am developing device using nRF52840 and i have question about analog pin usage.
My circuit is analog Pins getting voltage supply while nRF52840 is not used...
Hello Nordic team,
how is it possible to perform Packet Error Rate testing during an active OpenThread connection between two nRF52840 devices? The requested test scenario...
I am working with an app developer that is having trouble getting the DFU to work with my zephyr application. They are using:
https://nordicsemiconductor.github.io/IOS-DFU...
When I was considering the layout of the nRF5340 chip, I found that the pins of the nRF5340 chip are very small, and I need to punch the vias on the pads, and then use the...
