The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi,
This might be a simple one, but i cannot figure it out.. How do I place the rx/tx/rts/cts lines from UART0 on a GPIO1 pin?
In the piece of DTS below, 'tx-pin' is on...
nrf Toolchain: 2.7.0 nrf Connect SDK : 2.7.0 Gateway: nrF5340 Audio DK Headset: E arbud 'MOMENTUM TW 4' (Sennheiser) I try to run and test this following application Unicast...
Hi!
In my project i am using a motion sensor that uses a custom protocol. This has resulted in needing to implement bitbanging for it to work. The issue with this is that...
Hi,
I want to obtain the nrf52833‘s’ temperature with the SoftDevice enabled, and I have designed the code with reference to the example project. However, once the temperature...
Hi there,
I am trying to get nRFConnect working in VSCode, but when i click on things in the welcome screen it only shows "activating extensions..." in the bottom bar. I...
1) On p. 55 of nRF52805_PS_v1.4.pdf, section "5.3.8 Reset behavior" shows that a pin reset will reset GPIO, so will a pin reset active low also reset PSELRESET registers,...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hi,
I have built and run the MQTT sample for an nRF7002-DK and had it work as expected (connect, publish messages to test.mosquitto.org).
Now I'm trying to get that sample...
I created a new application using the "Create a new application" > "Copy a sample" > "zephyr/samples/basic/blinky" option in vscode. And I added a new build configuration...
Hi Nordic community,
I'm currently working on a project where I'm aiming to implement FOTA updates on the nRF52840 DK, with the application images stored on the MX25R64...
Both a colleague and I discovered that the default Device Provider, nrfutil, is not working in the current versions of VS Code and nRF Connect for VS Code extension. nrfjprog...
Toolchain v2.6.1 installed. Attempt to Manage SDKs fails.
[13:12:52] nRF Command Line Tools 10.24.2 are up to date Command failed: git ls-remote --tags --heads github.com...
First attempt to use the Power Profiler II on Windows 10 didn't work. I was getting [sdfu] No deviceInfo available for the device, code: Argument. Message: Operation device...
