Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
I am using nrf9160 custom board,my requirement is using external flash as secondary slot for mcuboot I have done configuration with respect to that in mcuboot and project...
Hey!
I'm working on a Firmware for a BLE peripheral device, I'm using the SDK version 17.1.x and the SD140 on a nRF52840. So far everything worked fine, I was able to...
Hi,
I'm trying to put my nRF52840 in System OFF and wake it up by DETECT signal on GPIO. For that I use gpio_pin_configure() with GPIO_INPUT | GPIO_INT_HIGH_1 flags but...
Hi i am involved in sdk5 based uart porting project
i can run example project and receive/send data to/from nrf52840-dk .
the problem is when i dig deep into the project...
Hi,
I am using a nRF52840 and SDK 15.2, and Soft Device S140 (BLE), where the device is battery powered.
In certain modes, the device sleeps to System Off mode, and...
I am currently porting the nrf_cc3xx_platform library to use it with RIOT OS . Following what has been done for Zephyr and FreeRTOS, I implemented:
Abort API
nrf_cc3xx_platform_abort_init...
Hello, I am working with the asset tracker v2 application and I want to connect it with Aws Cloud. I follow the steps corresponding to the tutorial and I am not successful...
I am trying to use the pc-ble-driver and as a first step want to use the heart_rate_collector example. I downloaded the source as follows:
I then followed the instructions...
Hi everyone,
I have an nRF52832 embedded as part of a dual chip (connected via SPI) and I'm looking to reduce the sleep current as much as possible. I'm currently measuring...
Hi, On both nrf52840 DK and Dongle, the sticker shows 4 info: - PCA board ID - version - year.month - Serial Number/MAC Address Could you please clarify what the last value...
Dear Nordic Community I am trying to get the nrfx adc driver to work with zephyr ( link ). With the help of this post , I ended up with the following code:
prj.conf -> ...
Dear Member,
I want to add ADC the main code,
but I got :
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol nrf_drv_ppi_init (referred from adc.o).
I'm using...
Hi, I am not sure whether there is I2C pins on nRF52840 Dongle board as based on the Adafruit Feather nRF52840 Express the pin is P0.11 and P0.12 as shown below: SCL 0.11...
Hello I am learning how to connect timers with gpio via PPI, i working on nrf52832dk.
So far I have connected the RTC 0 alarm channel to the LED no.3 (pin no.19) and its...
