Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
I am trying to scan for Bluetooth LE devices in Android with Java. Everything worked fine and I released an update and on fresh installs it does not work. I went through every...
I'm seeing an assertion failure at PC=0xa806 in nrf52840 + S140 7.3.0, while using L2CAP.
I know the most common cause for softdevice assertion failures is interrupt/timing...
Hi, I'm using nRF52805 and SEGGER. My BLE device disconnects with the mobile app occasionally. The disconnection happens randomly. In the debug mode, I see some messages....
hi,guys
I have a product that uses CHIP 52832qfaae0, and then I replaced chip 52832qfaae1, and there is A problem. Chip 52832qfaae0 runs normally with the same code, but...
Hello,
looking at the compatibility matrix for the 820 it seems that rev2 of the 820 can be used with softdevices and the legacy SDK v17, while rev3 can only be used with...
Dear Members,
I want to use SPI LCD and Sdcard, they have different CS, but sharing the same SPI ports, I have used different SPI instance but not giving us a good response...
On opening a sample project located at https://www.nordicsemi.com/Products/Development-software/nRF5-SDK with keil V5 , I can directly have an error message “Cannot read RTE...
Hi there, I'd like to make some FIR or IIR filter on my nRF52840 DK. I guess I'm supposed to: 1) Provide .a file into SES project's tree (or as Additional Input File): 2)...
I am working on OTA update .
Right now i am working simple
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_doc_user_guide_modules_dfu_configuring_performing...
Hi,
Is there any command for reading the type of Nordic SoCs (e.g, nRF52833 or nRF52840) that is going to be programmed by nrfjprog/ J-Link Commander?
Thank you!
Hi Nordic,
I want to write a value from the application layer to the bootloader flash region through uart, and use this value to replace the button 4's function of entering...
Hi All,
I'm using buttonless DFU for upgrading the firmware and my requirement is I would like to know the time taken for complete DFU from my application.
One approach...
Hi, I am working on designing specifications for a new product, which will potentially be using the NRF9160 as the main processor, since the main application is centered around...
