The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi,
with a custom hardware, I'm using a NRF9160 with a ESP8266 chip over uart with following prj.conf and board overlay:
I was trying to open a socket (that uses the...
Hi
The chip used is nrf52832, the SDK version is a peripheral device v13, and the central device uses v16.
The referenced example is ble_app_multirole_lesc and has been...
Background: SDK 16.0.0, SoftDevice 7.0.1, 1 ble_central connected 6 ble_peripheral, Send an instruction to 6 ble_peripherals every 50 milliseconds, at the same time, the ble_peripheral...
We need fast response from peripheral to central. That means we need a fast connection interval. We are using less than 100mS. But that results in an unacceptable battery...
Hi I have a question regarding USB port on the nrf52840 device When connecting a new device to computer is it possible to tell PC to assigne the same COM port number as last...
Hello, this is my first post in here. I'm trying to read the TX_POWER information of my beacons. I'm able to read this info using the nRFConnect app on my phone no problem...
Hi,
If I want to write a driver to control the communication process on nrf52840, the SDK is based on BLE mesh5.0.
How can I do it? do you have any examples?
Best...
Thank you ahead of time for any help that the community can provide. These forums have taught me a lot over the past few weeks. In my project, I am noticing 20x higher sleep...
I'm unable to get SPI to work on my nRF5340DK board. I can see activity on MOSI and SCK pins, but not on CS. The pin is not even initialized and is floating.
My overlay...
Hi,
During automatic assembly of the NRF52840-QIAA
We have found after Xray that we have air gaps surrounding ground pad vias - see attached images below.
I am...
I have a project that runs I2C to collect data from a pressure sensor and I have a different project that sends arrays of data over Bluetooth and they both work perfectly...
We are using RTC with external 32.768Khz clock to maintain and count a full date.
we found that we have a drift of time counting about 1 minute on every 10 nintues which...
I have the NRF52-DK, a 3-digit seven segment display, an RGB LED and a sensor. Using SES to try and get some basic code running.
I manage to open an nRF Connect SDK project...
