I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
Hello everyone,
I started with my program on the nrf52832. As a base I use the example multirole_LESC, because my focus is that 2 or more nrf52832 communicate with each...
Hi,
I want to storage some data in flash on nRF52810. When I open the "flash_fstorage" example and built it, there occur an error.
RTE\Device\nRF52832_xxAA\system_nrf52...
Hello,
I am looking to send packets of real time accelerometer data over uart to my PC via uart. The packets are similar to the code shown below where the data array is...
This is really bad, I downloaded the latest 1.7.0 SDK to the machine and could not build any application (including examples) Always appear errors
Create a GPS.Emproject...
Hi,
I have nRF9160 DK:
PCA10090 v0.8.3
modem firmware 1.2.3
The specifications says that the minimum consumption current is 7µA. So I flash a hex file which shuts...
(Using nRF Connect SDK 1.5)
I have the setup so far that partition manager is aware of the external flash and creates a single partition for it. The documentation section...
Hi nordic
I am using 52832 with sdk15.3:
when I program the hex with sd+APP+bootload, it works fine, while after the first ota, it will get the NRF_ERROR_STORAGE_FULL...
I have an encased nRF52840 dongle that is visible to nRF Connect. However, when I try and select the displayed device I get the following:
I cannot press the reset button...
Hi,
1. What modem versions does this board support?
For example mfw_nrf9160_1.3.0？
2. This board programmer this example:lwm2m_client
Using AT + CFUN? No return...
Dear Nordic team,
in our multiprotocol (BLE, ZB) application ( nRF5 SDK v4.1.0 )we are facing following severe issue relating to the ZBOSS stack: When a router leaves its...
Hello sir/Ma'am
I am working on a project in which i am using some BLE peripheral devices, an Central device and an Android app. I want to get data on android app from central...
I'm trying to program nrf9160 but getting an error due to readback protection.
I have tried the following commands:
nrfjprog --recover
nrfjprog --recover -f NRF91
...
I set an NOPULL type input GPIO, and I found that if I put in a voltage of about 1V,
the nrf52832 will produce a current of about 30uA,
I want to know why it can be happen...
