I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
I have updated the Programmer to v2.0, and connect 52840 with JLINK to my computer, but it can't be selected in Programmer. Previous version runs normally. What can I do?...
Hello! I'm trying to use an external module with the VSC extension and I don't think that is currently supported (or easily supported.) For reference, our module works with...
Hello, I'm trying to manage connecting to my board (nRF52840-DK) which direct advertise (low prio) with peer address set to MAC address of my PC running Linux with bluez 5...
Now I have a problem, the transmitting power of NRF52810-QCAA is too low, only -2.73dBm. I tried to adjust the value of the capacitor, but the effect was not obvious. Excuse...
Hi, I tested the RGB Led (with an external RGB Led) with the nrf 5340. But I didn't find any pinout with a brief overview of all the pins and their features because the PWM...
I'm trying to setup the SAADC, I do this as much as possible without examples, so I really understand what is going on.
Setting up:
After this I try to start an ADC...
Hello DevZone,
I am trying to build a NFC driver but I am getting issues with it reinitializing every time I detect a field.
I am unable to use the T2T and T4T libraries...
Hi,
nrf52833 custom board
My query is that how to do OTA DFU on ble central devices (we are using nrf52833 as receiver dongle(ble central) device)? Does anyone advice...
Hi all,
when I follow the blog as below, find the actual output is not same as expected.
Adding a Peripheral to an NCS Zephyr project - Peripherals And RF Test - nRF Connect...
Hi Everyone,
I recently purchased the NRF52840 DK with a PCA10056 designation. I connected the DK to my Windows 7 laptop via the USB. This resulted in the JLINK(D:) drive...
I have a custom board with a nRF52805 module but I don't understand how the SDK works.
I followed some guide to simulate nRF52805 software, I had to patch some files in...
Hello,
I add sd_ble_gap_phy_update() in the ble_evt_handler() as below:
case BLE_GAP_EVT_CONNECTED: { ...... ble_gap_phys_t const phys = { .rx_phys = BLE_GAP_PHY_2MBPS...
