I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
Hi,
I have a nRF51822 evaluation board and a nRF52833 DK.
Would it be possible to do Bluetooth direction finding with both of them?
I understand that nRF51822 is not...
Hi,
I am trying to measure my circuit sleep current while connected, through a high value resistor, the problem is while waking up each MIN_CONN_INTERVAL the processor wakes...
It is found that under the same routine in zigBee SDK, the project under pCA10056 folder can run normally without burning the protocol stack, but the project under PCA10059...
We would like to stream data through an l2cap channel from a nRF52840 module to a smartphone. The l2cap connection is initiated by the smartphone, I configured an l2cap tx...
I would like to test some compatibility features using the nrf52833 DK as a Bluetooth 4 transmitter instead of Bluetooth 5 (which it is by default). I do not see an explicit...
hi support team，
i have two questions from customer.
1. Monthly review suggested that Verizon certificate will be on October this year, how about he progress, we have...
I'm using the Nordic UART Service to implement BLE communication between an iOS app (central) and a Raspberry Pi (peripheral). Whenever I send a large payload to the central...
Hi,
We are using Nordic thingy 52 HW and their SDK for our Evaluation purpose. We are using Nordic thingy 52 microphone code directly. That firmware is using ADPCM codec...
Unable to connect to Bonded weara with GATT 133 error. Currently, there is only one solution, turning on and off Bluetooth in the OS, which temporarily improves the connection...
Hello
new nRD5 SDK v17.1.0
Can you please help me to find more about:
1. "- NRFFOSDK-13484: Added an option in the Peer Manager to decide that a connection will not...
Hello,
I am currently developing an application on a single core application. I need to add a BLE part to this application. Currently, I have an OTA update procedure that...
Hello,
I'm trying to open an L2CAP connection and send some test data to the nrf52840 dev board from my computer. But my connections were timing out with 'Page Timeout'...
Hi ,
I have a question ,according to the official configuration and example, the ADC sampling voltage value is smaller than the actual voltage value. For example, the actual...
I have nrf52832 dk and soft dveice s132 am using ble app template code.
I need help in this code that as:
1. as i flash the code on dk, the device should be initally in...
