You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
On a recent run of prototypes using the nRF9151 and the nPM1300 we've had a few failure where the nRF9151 cannot connect to the debugger and the board exhibits much higher...
I have two nRF9151 DK boards, both hardware revision 1.4.0, both showing the same SIM detection failure.
Symptoms on both boards:
AT%XSIM? always returns %XSIM: 0,9...
We have purchased a radio fitted with the nRF9160 modem and fitted it with a roaming SIM for NB-IoT use, we are in UK and have Band 20 EE and Vodafone.
What are the initial...
Now my product need FCC, and I use DTM example, only changed the txd,rxd pin in firmware, the lab can use nrfconnect for desktop to enter test, but the tx power is low when...
Dear Nordic,
I'm designing a 0.6mm thick 6-layer rigid-flex with the nRF54L15-CAAA, and due to my current stack-up the ground polygon to trace clearance can only go as small...
Hi Nordic Team,
Could you please clarify the SDK/NCS compatibility for the nRF54L15-CAAA chip?
We are planning to develop firmware in bare-metal mode and would like to...
Hi For a product, I'd like to have (well it's a requirement) the firmware update encrypted. So I set the following in sysbuild.conf: ... SB_CONFIG_BOOT_ENCRYPTION=y SB_CONFIG_BOOT_ENCRYPTION_ALG_AES_256...
Summary
On a small fleet of identical nRF52832 units running the same firmware (NCS 2.5.1, SoftDevice Controller, BLE peripheral, LFCLK = RC with calibration), individual...
I want to implement a BLE composite device with BLE UART and BLE HID, and both services can work at the same time.
Hello! I want to make a Bluetooth game controller, and...
Dear Nordic Experts.
We designed a device based on the nRF54LS05B module.
We are writing a production test program and using nRF54LS05-DK Rev 0.3.1 for verification. ...
We are using monitor mode on the nRF7002 to receive packets in promiscuous mode. We are on NCS 2.9.1. The Wi-Fi packets we receive have the follow header (struct copied from...
The nRF Thread Topology Monitor is a very useful bit of software. It would be very nice to see it updated, or perhaps even made a first-class member of the nRF Connect for...
Can you pls send recommendation document for the exact foot print to be used for nRF54LM20A-PAAA CSP98 BGA?
I have found reference foot print BGA98N35P10X10_385X367X68.dra...
Hi
I am developing RX device to connect with Smart Remote 3.
The RX device system is Linux embedded. I need to run OTA function in Linux embedded to update SR3 F/W.
...
