The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi Sir,
For nRF52840, we have a layout guide, nAN-40, can reference.
For nRF9160, do we have the information of land pattern or similar document can reference?
Thank...
Hi,
In a project I am working on with the nRF52840 I will need the ACL to protect a private key in the flash memory. With help from another post here I put together the...
Hi,
I am using an nRF9160 dev-kit and I am debigging some connectivity issues.
Unfortunately there is some random bahaviour on the Serial Interfaces, which are exposed...
I am a recent student interested in Nordic. I know that my skills are very, very poor. Sorry for asking this question T_T I want to use i2c sensor vl53l1x. I tried to refer...
Hello,
I am developing a Zigbee coordinator with the nRF52840 DK and with the nRF52_SDK_for_Thread_and_Zigbee_v_4.1.0. I flashed the CLI example and everything works fine...
Hello,
could you advice me where can I find description of nRF5 anomaly 211 - the one described in nRF5 SDK 17.0.2?
Citation from 17.0.2 release notes:
...
...
Hi,
I intend to use the DFU BOOTLOADER in my product.
I’m using a PCA10040 DEV board for the tests with S132
I download the nRF SDK V17 and I compiled and I tested the...
I understand that nRF-9160 DK has Segger J-Link to program target devices / custom boards. Can this be used to program any ARM Cortex Debug Connector (10-pin)? Or I can program...
Hi. I am using nrf52840 with Softdevice 16.0.0 + BLE_uart_peripheral.
The SPI master transmits 2 SPI packets every 10 ms. At the the SPIS event handler, I call ble_nus_data_send...
I am seeing an issue when, after the pairing process is complete, during the BLE_GAP_EVT_AUTH_STATUS event, that the peer addr_id_peer field is always 0. For testing, I am...
My platform is nRF5_SDK_16. Softdevice is s140_nrf52_7.0.1_softdevice. I want to be the central role and scan nearby peripherals. Which function do I need to use? Which document...
I am totally new to nrf and just started with nrf52840. I've gone through certain tutorials available on youtube and some other on internet.
I've installed Segger embedded...
Assume that the Generic Level State is 0 and the following Generic Level Set message is received by a node.
Level: 0x7FFF Tid: 1 Delay: 0xFF (1275 ms) Transition time: 0x00...
I haven't been able to crack this one. Both pins confirmed as pull-up high using I notice when the peripheral is enabled the pins are pulled low (correct I think). Only sending...
Dear Nordic Developer Zone,
I want to change PHY configuration of ble_app_uart to 2Mbps.(SoC : nRF52811)
And I want to connect nRF52811 with iOS.(nRF connect for mobile...
