Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi All,
When working on NCS with SEGGER Embedded Studio Nordic Edition (v5.20b), modify prj.conf will not reflect on rebuild solution.
It seems the IDE doesn't update...
Hello Nordic Team,
i've been evaluating the nRF52833 and i have been having a lot of good success. i have been focused on the SAADC block to ensure it meets my performance...
Hi
Since we need use different C1/C2 (15PF/12PF) for 32.768K XL1/XL2
I check "https://devzone.nordicsemi.com/f/nordic-q-a/37448/asymmetric-crystal-load-capacitors" , and...
Hello,
I'm using nrf connect 1.4.0 and nRF9160 dk
I started testing the aws_iot example. It worked fine with my was set up and was able to see the shadow updated.
...
Hello.
I'm using nrf52833 / SDK 17.0.0
I want to find out SAADC sampling time by using logic analyzer.
However, I still don't know what sampling time is.
In this...
Hi
We are working on the secure DFU. The issue is that the NRF52832 chip resets when switch to the DFU mode. All the GPIOs are turned off during reset. However, one of the...
Hello ,
I am working on nRF52832 using sdk 16 version .How to change the device name dynamically . Actually I want to set the device name via BLE command from the application...
I wonder if the nRF5281x can work in the "LE Advertising Extensions" mode, which seems to be like in Bluetooth 5.0, when data is transmitted by secondary advertising packets...
Hi,
I would like to ask if there is any program which i can use to update firmware Over The Air on nRF51822 chip from Windows command line. I know there is that possibility...
Hi,
I understand that NRF connect source code is unavailable.
However the toolbox Nordic App is too heavy.
Is it possible to get a small Scan Android App source code...
Hello I use nrf52832 and sdk v17.0.
I'm using a battery and I can check whether the battery is charging or not. And I'm going to turn off the Bluetooth function while the...
Hi,
I started a project from scratch and I want to write a simple UART printf solution for debugging for my NRF52832 on PCA10040 DK. I know there's a LOG module but it...
I'm working on a BLE peripheral that will connect to both iOS and Android devices. It is important to maintain connection during usage so I consider increasing supervision...
Hi! Are there any existing solutions to send the NRF_LOG output over BLE or to write it straight to a flash/SD-card? If not, would editing the macro's in nrf_log.h be an appropriate...
Hello,
I have a gateway project where I need to receive data from BLE and send on ANT network. As a first step, I took the NUS or ble_app_uart and changed the softdevice...
