Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I would like to switch to using libUARTE for both of my UARTs but I don't have any additional timers free. Is it possible to do this and use FreeRTOS timers?
Thanks,
...
Hi,
We would like to interface with our nRF52840-DK from a PC.
We need to be able to send\recieve data from PC -> 52840 using Nordic's UART service.
We are looking for...
Hi,
We are the company which widely use your products in our devices. Currently we have the nRF9160 based device which have permanent trouble with radios. I want to ask...
Hi All,
Is there a tool or app that shows a visualization of Thread RSSI?
Any help would be appreciated, thanks in advance.
Best,
Tao
Ref:
https://devzone...
Hi,
I am developing both Central and Peripheral devices with nRF52840. For consistency, both are using SDK 15.3.0 and S140 V7.
I am able to connect to peripherals and...
Hi,
I was try to import modul nrfxlib in extising cmake project. My IDE is Eclipse CDT. Version of Zephyr is 2.4.0. Reason to do that, was testing SoftDevice BLE functionality...
We are using our board design using nRF52840.
During bringup I noticed that I could not run the Softdevice and the SPI driver simultaneous. After a bit of debugging it boiled...
I'm trying to send radio frame in timeslot but it's not working. From what I see with an spectrum analyzer, only the first frame is sent.
I am able to make the radio works...
Hi,
We are developing an application with a custom nrf5340 board in which beacons are sent periodically every 100ms. We have been analyzing power consumption with a Power...
Hi there!
We faced the problem of not being able to perform Legacy DFU with Android 10 and newer iOS devices and have since applied the fix. However, since doing so we observed...
Hello,
in our design we use a RF switch behind the ANT LTE antenna I/O of the nRF9160. Many RF switches need DC blocking capacitors in series with the RF signal due to their...
Hi everyone,
When we want to enable a module we usually enable it from the sdk_config.h by setting the desired module to 1 (for example #define NRFX_SAADC_ENABLED 1). I...
Hello, I am using nrf52810 and S112 Softdevice.
After initializing uart, use uart close for uart sleep.
Then the uart close will be checked.
I want to make an uart init...
I have an nrf52832 based device and a mobile app that I'm working on. I'd like to be able to turn the device on via the app, so wake on BLE seems the way to go.
I'm a neophyte...
