Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
Hi
Getting problem in DFU feature while using segger embedded studio.Device gets programmed successfully but stops working after that.
I am following the same process...
I am trying add UART functionality in nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader.
After adding all required files and compiling program I am getting following error...
Hello I am using nrf52832 and I want to Calculate date and time at specific event periodically and save it to flash,so is it possible by using ble_app_cts_c example or any...
as title,
I can't load the project to SEGGER Embedded Studio.
I can't install CMake by entering the those command ( choco install -y cmake --installargs 'ADD_CMAKE_TO_PATH...
Hi
I was trying to do the page up and down key, I just built it successfully but it is no response.
Could anyone find out the reason for me.
I appreciate for your assistance...
Hello,
I tried to follow the "nRF_Sniffer_UG_v2.2" and i didn't understand the section 1.2 which described how to set the Python and Pyserial,can some one explain what to...
Hi,
1. Can one run the coexist sample with softdevice S132 on a mesh where all the other nodes run S140?
2. does the coexist (UART) example need to be provisioned. ...
Hello to everyone.
I'm working with the Light_Switch example with four nRF52832 SDK (two clients, two servers) and my cellphone as provisioner, in Mesh 3.10, with "nRF Mesh...
Hi again, Figure 106 in the OPS indicates that the application core and the modem core in the nRF9160 have separate Flash and RAM partitions.
Is this a "real" partition...
Hello,
I ordered my nRF52 DK from Rigado for their BMD-350 module using the nRF52832 chip, but their DK comes with an additional Atmel chip. Now I saw the regular nRF 52...
Hello!
In SDK15.3 project "secure_bootloader_ble_s112_pca10040e" for Keil , write flash incorrect and not work.
In SDK15.2 this prodject work fine.
Please correct...
My application will update over USB from a connected host.
For testing, I used two projects:
Bootloader: secure_bootloader_usb_mbr_pca10056
Application: led_softblink_pca10056...
So im trying to interact with a nrf52 chip. I am using iOS corebluetooth to communicate with the device and when the device sends a long data packet (~400 bytes) iOS drops...
Hi,
I have my SAADC configured with two channels. One for my sensor and one for the battery level measurement.
I only need to measure my battery level every minute for...
