The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
Hello,
I want to store some values to flash. What is the best method to store data to flash?
I'm trying to get pstorage working but i have no luck, so i'm wondering...
Hi,
I'm trying to run the Template app on a beacon but am not having much luck. So far I've been able to run it on the nRF51-Dongle but it appears dead on the beacon. ...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hi,all. i faced a problem:when i take my phone far away from my device,link-lost severce can work,but turn bluetooth switch off on my phone directly,my device can't alarm...
Hi,
I am trying to upload dual_bank_ble_s110 example on nrf51-dk using Keil. But it shows error:
C:\Program Files (x86)\Nordic Semiconductor\nrf5x\bin\nrfjprog.exe...
Hi, I am trying to generate PWM pulse based on sample application in GitHub. However instead of using different modes and multiple channels, I tried to simplify it to just...
Probably a silly question, but I am new to Nordic Semiconductor and can't figure this out. I am trying to make a new project based on the Template example for nrf51422_xxac_s100...
I am writing my own function to setup a notification characteristic, but it failed,
Could anyone help me check it ?
static uint8_t d[2] = {0};
static ble_gatts_char_handles_t...
I have been experimenting with mbed ble programming and have had some success with the examples and my own programs. Everything works fine on the nRF51 dongle and DK.
I...
I'm trying to enable the active signal for an nRF8001 on Adafruit's breakout board. Is there a way to do this without using the nRFgo software? I use a Mac so setting up nRFgo...
Hello.
I use BLE Shield V.2.1 of RedBearLab.com for Arduino.
The shield equipped nRF8001.
After about 62ms from reset nRF8001 by putting Low signal in Arduino pin 4...
Iam using NRF8001 in my project & i don't know how to enable them & connect them through Android app basically iam using in tracking chip so any one have a idea that how to...
I am using an Arduino and NRF8001 break out board from Adafruit. I am using the UART profile (adafruit sample code) to send data between mobile phone and Arduino. However...
Hi,
I am trying to setup the nrf8001 by sending the setup commands from my microcontroller. After I send the complete setup packet (21 commands) I receive, as expected...
