Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello, according to the Product Specification v3.1, the supply voltage range is 1.8 V to 3.6 V.
As you may know, most of the lipo batteries have a nominal voltage of 3.7V...
I am following the NaN-36 example... So far all is going well but i am stuck at section 4.5.4 . I have checked over all the directions three or four times... I have to be...
I am hoping someone can point me in the correct direction as I have posted my question on the SIG forum and didn't receive any responses.
With a nRF51422 device is there...
I've followed the instructions for adding the DFU service to my app to the letter and can see the DFU service from the central and can enable notifications on the control...
Hi.
nrf51x22 has 32 IOs. can we assign 2 pin to usb d+, d-, and listen interrupt.
yes, nrf51x22 has uart support, but many host device only have usb port. serial port...
Hi All,
I am using NRF51822 chip pca10001 development board.
I flashed ble_app_hrs application to the board.
I configure 3 channel for PPI.
static void ppi_init...
Hello all,
I'm writing code for the nRF51 to allow it to be driven via the Android ANT SDK (from Dynastream), using standard ANT protocol messages.
However, it's occured...
Hi,
I'm using the nRF51 DK as a BLE sniffer with your Wireshark plugin. I have several BLE peripherals in the same room I'm testing it so it will be useful to filter data...
Hi, I'm newbie developing with nRF51. I'm working in Firmware for a ble central role that can read all the macs of ble peripherals roles near. I want to event or function...
Hi all,
I've a problem that drives me crazy for some day.
I installed all SDKs, and trying to write some BLE apps. Everything works fine but i cant't find where pstorage_access_wait...
Hi,
I want to implement stack tracing to check stack overflow and remaining stack. I followed the implementation given in example github.com/.../memory_watcher.
Memory...
Hi
I am coding a s130 NUS example.
The base example is sdk8.1.0 ble_app_uart peripheral example.
I added central part from Github sdk8.0.0 ble_app_uart_c...
