Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
test the gpiote_example for timer0 in pca10003, the function is ok, LED blinking 200ms. but I change the timer0 to timer1 or timer2, the LED always on,and never blinking....
Hi! I use S130 on nRF51822 device.
After device is connected as peripheral I try to discover services using Master Control Panel but device disconnects. In Master Control...
I'm trying to start advertisement after establishing peripheral connection (on BLE_GAP_EVT_CONNECTED event) but called function sd_ble_gap_adv_start(...) returns NRF_ERROR_INVALID_STATE...
Hi
I'm working on a project to drive a DC motor, I really didn't find any example. I would like to know how can I program a pin in Keil, and I would be happy to have a...
Hello,
I am trying to get a lower connection interval from iOS. But the lowest connection interval I could get were 30ms.
Anyone has experience to achieve the connection...
Hi.
I find this code github.com/.../nrf51-dfu-single-bank-ble
I want to compile bootloader and download it on PCA10004.
I have KEIL 5.12 and the project file of the link...
Hi,
I want to create a service for test logger. Through this service i want to write n bytes at a time and after few delay want to write again some n bytes. These written...
I'm struggling to get started using Keil with an NRF51822 mounted on a custom board that I have cobbled together.
I have opened the blinky/pca10031 example as a starting...
Hello, I have two nRF24L01 devices that can already talk to each other on a custom address. When I try to talk to the nRF51822 from one of the nRF24L01 devices, I cannot get...
services.h
Hi,
I'm writing an interface for my nRF8001 and am a bit confused about the NB_SETUP_MESSAGES value. In my services.h file the value is 14 when it appears there...
May be i haven't seen it, but how i can select if the setup will be stored in the NVM or volatile storage.
I prefere to start development with volatile storage.
On Page...
Dear All,
I used the array defined in services_lock.h to setup the nrf8001 module. Therefore, the service setup is written to the OTP memory in the chip. Now, I want to change...
Hi
I tried to connect our non-bonding device to Windows 8.1, but it ends in an error message. The implementaion uses the device_manager_peripherial from SDK 6.1 with the...
I am using the nRF8001 and trying to do ANCS. After rebooting the Arduino / BLE Shield, I have to reset Bluetooth in iOS in order for ANCS to work again.
I was thinking...
