Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
There was a question when doing the multi-channel test of ANT. The SDK is 17.1, and the example is (ant / ant_ multi_ channels)，Encountered the following problems：
1、Example...
I have
nRf52840 DK - 1 - Mesh Serail example nRF52840 Dongle - 2 - Mesh Light Switch Server example.
I used the steps given in the infocenter to provision and configure...
Hi,
Is it possible to be in connected mode (exchanging data) and also advertise data packet (on primary channels) between two BLE devices (so, in both the modes) ? Is there...
When using nrfjprog over an IP connection, `--ids` never returns a value. This is frustrating as the Zephyr nrfjprog runner uses this command to determine if there is a board...
Hello !
In latest errata, https://infocenter.nordicsemi.com/pdf/nRF52840_Rev_3_Errata_v1.1.pdf is not so clear all details of this anomaly
[254] RADIO: External PAs, FEMs...
I am trying to port a timer over to the nrfx_rtc driver and I can't seem to get it to start counting. I'm sure I'm missing something small, but I'm not seeing it. SDK 17,...
Hi,
I have a medical device where my mother board has a NRF52840 chip which communicates with a Android Tablet through blue-tooth. We find it gets connected with few tablets...
Hi, I am working the Zigbee in nrf connect SDK 1.9.1 I am running light_bulb, switch and coordinator examples
I want to change the panid , Short id, via proj.conf
how...
Hi,
Greetings!
I am using below setup
nRF52832
Mesh SDK 4.0.0
SDK 16.0.0
Application Example: light_switch_client_nrf52832_xxAA_s132_7.0.1
Issue:
Using above...
I am using SDK 17.1.0 with an nRF52832 design similar to the P10040.
I was previously using the original timer application and things were looking good. I decided to upgrade...
SDK: NCS 2.0.0
Based on: Peripheral LBS example
Central: Mobile (iPhone)
Peripheral: nRF5340
IDE: VS Code
Hi Everyone,
I am porting an existing project based...
Hello All,
We are intending to start a new project using nRF52840 SOC, for the same i decided to work with nRF connect SDK as it is recommended by nordic,
I am new to...
Hi everyone
We have developed a smartwatch with a nrf9160 chip. We have used nrf Connect SDK 1.2 for the development process.
Now we want to migrate our project to nrf...
Hello there,
I am using the peripheral/radio/transmitter and receiver example in SDK17
But I am only able to transmit 2 bytes. I want to transmit like 8 or 9 bytes...
Hi,
I am testing FOTA function using sample "http_update/application_update" on NRF9160DK.
But found that the system boot stuck at
I had tested this sample with...
