Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Hello,
I am successfully able to open and close adapter for nRF52840 using pc-ble-driver-py using python3.6.0 on my host armv7 Linux board.
But doing same inside the docker...
Hi,
We are developing BLE firmware that will allow BLE pairing without bonding (but with PIN/Passkey that is entered from the phone). However, when I try this with nRFconnect...
Hello Nordic Support.
I would like to build and use a Sniffer using a PC (Windows 10), nRF52DK, and nRFConnect for desktop.
Please teach me about the following.
nRFSniffer...
Hi, I can successfully build the Matter light bulb example in nRF Connect SDK 1.9.1 but I fail to do the same in v1.9.99-dev1.
What did you change?
Here the error:
west...
Dear DevZone support team
I'm facing the following problem: My application uses the Zephyr's BLE stack and basically does not much beside parsing JSON-messages received...
Hi,
I tried to implement PPI for a very timing sensitive application. The sample PPI_trace uses the RTC but it is too slow for my application so I'd want ot use timer0...
Hello,
We would like to use BLE to transmit a lossy data stream at high data rate. Looks like Isochronous channel is the best choice. How's the Isochronous channel is...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Hi,
I work on an AOA projet and i have a problem.
I have already made a transmitter (with an nRF52833) and a receiver (also nRF52833) and i can see the CTE send by my...
I need to add a custom BLE service with over 20 custom characteristics. During the gap nitialization step, I set the BLE security mode and security level like this:
sec_mode...
Hi ,
Am following the below link https://devzone.nordicsemi.com/f/nordic-q-a/83402/ncs1-8-0-52840-mcuboot-spi-external-flash-can-t-build-pass ,
am able to build it for...
hello,
i am using nrf52832 with accelarometer i want to put my board in shutdown for current consumption for that i am giving this command sd_power_system_off(); whenever...
I need to be able to change the device name the SoftDevice uses AFTER the soft device is up and running. To change the device name, To do this I use
errorCode = sd_ble_gap_device_name_set...
Hi,
I currently have a macro in the nRF Connect Mobile app (Android) that displays RSSI every time I receive a temperature signal. I am saving the logged temperature and...
It seems that not all UICR registers are erased on this nRF52840 chip
nrfjprog -f nrf52 --recover
Just make sure one more time:
nrfjprog -f nrf52 --eraseuicr
nrfjprog...
