Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Greetings, I am developing an application for the NRF52840 in a RAK Wireless RAK4631, using the Arduino BlueFruit libraries.
When I monitor NRF_RTC1->COUNTER variable, it...
Hello everyone,
Because of problem with availability we were forced to change our ready-for-production project from nRF52832_xxAA to nRF52832_xxAB which has 2x less FLASH...
Hi, there
I am using nrf52832 chip on a custom hardware and also using softdevice 132 to send data to an app.
I need to send data from app to MCU and vice-versa and...
Hi
I am using the nRF52832DK and the BLE_App_Blinky.
I have a stable BLE connection to a phone and then I try to close the connection inside the nRF with sd_ble_gap_disconnect...
Hi, I am trying to implement Azure FOTA using your libraries. My source code is a combination of the Azure iot sample and the Azure fota sample + some necessary alterations...
As I know,the New Order Code of nRF52 Series has added Access port protection Controlled by hardware and software function, the earlier order code : Access port protection...
Hi, I'm working on updating nRF9160 modem firmware update.
I have update modem[mfw_nrf9160_1.3.1.zip] using nRF connect Desktop application and read partition using nRF...
Hi
I run nRF connect SDK 1.7.1 and have a custom nRF9160 board.
I'm trying to get the I2C peripheral to work with my own hardware.
I have read and googled all tutorials...
Hi,
Can I use the hex file compiled for nRF52810 for nRF52805 directly ? Please note that I am not using any peripherals other than radio.
Can I use the nRF52810 build...
We use the nRF24L01+ in a dedicated RX mode, and it is preceded by a power splitter, filters and LNA. In order to run some system calculations, I'd really like to know the...
We are using nRF52840 on a custom board with nRF5 SDK v15.3.0.
Our application uses the NFCT driver (nrfx_nfct) along with nfc_t2t_lib_gcc.a to emulate a NFC tag with some...
HI,Therd:
I used the mesh sdk 5.0.0(BLE SDK 17.0.2), and run the example light_switch_server_nrf52832_xxAA_s132_7_2_0.emProject. when i use the nRF Mesh app on the phone...
Hi,
I am evaluating nRF53 for ZigBee in a Linux application that implements a MQTT-SN Gateway. I am interested in learning about Linux board can connect to the nRF53 (USB...
using nRF5 SDK 17.1.0
Segger
I need some understanding of the QDEC. if I connect a motor that has a A/B output at a 5KHZ rate.
what is the maximum rate at which the...
