Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi Nordic Team,
Could you please clarify the SDK/NCS compatibility for the nRF54L15-CAAA chip?
We are planning to develop firmware in bare-metal mode and would like to...
Hi For a product, I'd like to have (well it's a requirement) the firmware update encrypted. So I set the following in sysbuild.conf: ... SB_CONFIG_BOOT_ENCRYPTION=y SB_CONFIG_BOOT_ENCRYPTION_ALG_AES_256...
Summary
On a small fleet of identical nRF52832 units running the same firmware (NCS 2.5.1, SoftDevice Controller, BLE peripheral, LFCLK = RC with calibration), individual...
I want to implement a BLE composite device with BLE UART and BLE HID, and both services can work at the same time.
Hello! I want to make a Bluetooth game controller, and...
Dear Nordic Experts.
We designed a device based on the nRF54LS05B module.
We are writing a production test program and using nRF54LS05-DK Rev 0.3.1 for verification. ...
We are using monitor mode on the nRF7002 to receive packets in promiscuous mode. We are on NCS 2.9.1. The Wi-Fi packets we receive have the follow header (struct copied from...
The nRF Thread Topology Monitor is a very useful bit of software. It would be very nice to see it updated, or perhaps even made a first-class member of the nRF Connect for...
Can you pls send recommendation document for the exact foot print to be used for nRF54LM20A-PAAA CSP98 BGA?
I have found reference foot print BGA98N35P10X10_385X367X68.dra...
Hi
I am developing RX device to connect with Smart Remote 3.
The RX device system is Linux embedded. I need to run OTA function in Linux embedded to update SR3 F/W.
...
While debugging the code with Nrf connect extension in VS code , code get stuck at the start only does not go any where getting the SIGNTRAP error continuous
Hi,
With the latest SDK v 14.2 is it possible to do OTA updates to nRF52 from OSX/Windows/Linux without the use of additional DK? I understand that for iOS and Android...
I'm tring to build a FOTA broadcaster machine using a raspberry-pi with bluez. or any other Linux small linux embedded system.
The idea is that after testing the board...
Hello, I want to use ble dfu on nordic. But most examples work with Adroid App, and I need nRFxx transmit dfu to another nordic. Can you tell me if vag has ready-made examples...
Hi,
I need to output a continuous 16 MHz clock on a GPIO pin on the nRF54L15.
I first looked at the GRTC clock output, but since the fast clock is divided by (CLKFASTDIV...
Hi, I am developing a program for the nRF54L15 with the DFU bootloader enabled. I would like to reduce the startup current.
I am using SDK 3.2.4.
The `sysbuild.conf` settings...
