Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hello guys good Morning,
I am currently studying the examples in the Nordic Dev Academy. I am in lesson 5 from the "NRF Connect SDK Fundamentals", and I managed to toggle...
Hi,
I'm attempting to restore my Thingy91x to communicate with my instance of nRF Cloud (I had removed the certificates previously to test out the connection to another...
Hi,
I am using a custom nRF52832 board with multiple ADC channel readings sequentially. I am trying to read thermistor (NTC) value on channel 7 and not getting accurate...
Hi community,
I'm using the following setup:
nRF5340DK
nRF Connect SDK v2.6.0
B0 , upgradable secure MCUBoot, and application
Statically defined partitions in...
Hi,
My requirements are:
My essential need is a one-to-one connection between central and peripheral .
But when my central receives the specified command to start scanning...
Hello there, this is my first post here.
I'm facing a wall in my project development.
Here is the issue, so during start up of the NRF52832 I see a high current draw for...
Hello, I need your help about BLE channels. Currently, I use only the primary channel 38 for advertising data but, when the data are sent, I don't have the information of...
Hello,
I am currently working on connecting a Thingy:91x to a Cube Orange autopilot (Pixhawk 2.1) in order to receive telemetry data over UART using the MAVLink protocol...
We need a parter to develop the Thread terminal base on Nordice nRF52840, the project will be design in China and produce in Germany. Is there any reliable company could provide...
I noticed that through apply_old_config.h configuration values like NRFX_CLOCK_ENABLED in sdk_config.h simply get overriden by the old CLOCK_ENABLED, so that there is no point...
The scanner can be informed of the synchronization information as soon as it receives an ADV_EXT_IND PDU, and then it can later scan only AUX_SYNC_IND PDUs. at this point...
I am using NRF52832 Custom Board and Have to implement deep sleep for 1 minute and have to limit the current consumption to a very minimal value during the sleep cycle I have...
I am trying to get the J-Link RTT viewer working with the Sysbuild Peripheral LBS Sample from the BLE FOTA DevAcademy lesson . I need the SEGGER J-Link RTT viewer working...
Hi everyone,
I have an interesting issue to discuss. I'm developing a BLE peripheral based on Telit BlueMod +S50 (nRF52832) & NCS v2.7.0. I send data on regular, long intervals...
I get the error "ImportError: Module use of python312.dll conflicts with this version of Python." when I try to flash my device using any Python version below 3.12.x. I get...
