Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I am using SPIM in nrf5340 to read datas from 2 sensors. The sample rate is 400Hz, and I have to send and receive 8 bytes to each sensor every 2.5ms.
So I set up one...
Hello,
I want to judge the end of a file. In the past, I can directly call the feof() function when writing in C. Now I call the api in "fs.c & fs.h" in the example of zephyr...
Hi,
On a nRF52840 based coordinator, I want to support Zigbee 3.0 install codes and legacy devices with HA predefined link key at the same time.
1. Is that possible by...
I am working on a device driver for the W25Q128JV flash device. This is the first SPI device I've used with the nRF52840. I had some observations and questions about SPI programming...
Hi - I've bought two nRF5340 DK kits for some development work - and after about a week's effort and searching Nordic Semi documentation, Youtube and the internet in general...
I develop my own device on nRF52840 which will be HID device. And I have made my own HID descriptor of device:
And if I send data with function from example:
...
Hi,
As an alternative to writing a configration software for my device (a native app for windows or maybe android) I,m considering putting physical controls on the device...
I've installed Zephyr RTOS and built blinky example for NRF5340-DK board. Then, when I tried to flash output hex file into NRF5340, nrfjprog (using "west flash" command) gave...
I'm trying to debug firmware on our production device, but after programming the device a couple of times, I am unable to program.
Inside of Segger I see this log:
j...
Hi everyone,
In my company we are working with the last SDK release, and we build projects with make and gcc toolchain.
I have a quite wide request : since I'm using makefiles...
Hi all,
I have a custom nRF52840 board that transmits 32-byte packets to mobile device and I want to achieve maximum transfer speed.
The code is based on the ble_app_uart...
Dear all
The issue is:
heartRate and battery levels set by "bt_gatt_notify" in peripheral hr sample on nRFConnect v1.5.0 are not shown in iphone app of "nRF toolbox" ...
Hi All,
I am using the nRF52840, with SDK140 v15.0. I have configured the nRF52840 to be a SPI slave to a NXP processor. When I connect the logic analyzer I see signals...
Hello,
I am trying to build on the nrf5340_cpuappns sample, however this snippet seems to always warn unable to allocated UART send data buffer. Is there any reason k_malloc...
