hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
I am trying to make the nRF24LE1 as a sensor node. So I want to configure it to work as a receiver/transmitter and simultaneously use the ADC and UART. But the moment I added...
Hi all,
I'm using nrf51822 and ble_app_multirole_lesc example on SDK 12.3.
When I connect with "nrf connect" Android application for the first time, the bind is established...
Greetings. Finally ordered some NRF52832 board from HOLY IOT and spend few weeks trying to handle with them.
So, all about setup:
SDK: 15 (15.0.0_a53641a) @ Windows 7...
Hello, I have just started evaluating SoC nRF52832 and have built a custom board based on recommended diagram from the datasheet chapter 53.3. Actually, the board diagram...
Config
Using NRF52810 on a custom PCB with 32kHz + 32MHz crystals, very close to the reference schematic
S112 with SDK 14.2.0 in SEGGER Embedded Studio V3.30
A button...
In my application, I execute below code to start advertise when a button is pressed
err_code = ble_advertising_start(BLE_ADV_MODE_FAST);
APP_ERROR_CHECK(err_code);
...
Hello,
I am developing an application using the nRF51422.
For flashing and debugging the nRF, I use a ST-Link V2 debugger which uses SWD. The IDE I use is uVision.
I...
Hi
I have been succeed test SDK15.0.0 i2s example and got UART data.
UART started.<CR><LF> NRF_LOG_DEFAULT_BACKENDS_INIT started.<CR><LF> NRF_LOG_DEFAULT_BACKENDS_INIT...
Dear Sir,
I am working on SDK15,nrf52832 and soft device S132.
I was working on the following scenario.
A peripheral device advertise as soon as it is switched ON. ...
Hi, nordic
I get some problem when developing the ancs with SDK15.0.
I run the demo with ble_app_ancs_c on the board of PCA10040.
First of all, after my iphoneX (system...
Hi all, development software: nrf5_SDK_for_Mesh_v2.1.1_src\examples\light_switch\proxy_server Board 1 nrf5_SDK_for_Mesh_v2.1.1_src\examples\serial Board 2
IDEs: SEGGER...
Hello,
I am using NRF52832 boars s132 and sdk is 13.1. I have developed my application is read analog accelerometer valie and send to mobile apps. Now i want to also battery...
I'm facing one issue while uploading firmware using BLE DFU.
Details:-
Hardware : NRF52840-DK
SDK : v15.0.0_a53641a
IDE : Segger Embedded Studio v3.40
Mobile App...
