The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi,
I have to transfer messages every 100ms and to receive confirmation about successfull reception.
Message is sent from the phone and should make two hoos and return...
Hello,
I'm using the PWM peripheral to generate a waveform. The waveform is loaded into RAM and then I use the SEQ[n].PTR and SEQ[n].CNT registers to set up the DMA. The...
Hi to all,
i am working on a project based on nrf51822 soc, i want measure level of battery with nrf51822 ADC channel.
i have an example code that measure the level of...
Hi all,
I can't get the Blinky example working on my PCA10040 kit. After flashing, LED1 stays on and there is some activity on LD5 but the kit is not detected on all my...
Hello,
I'm currently developing an application using an NRF52832 and SDK15 (SD 6.0.0). I have an issue that causes an UART overrun during some flash operations and it somehow...
I was wondering if it was any use to make use of gains 2 and 4, and noticed the errors for those gains are missing in the PS.
So do gains 2 and 4 actually increase the resolution...
i want to sinchronyze diferent peripheral and 1 central thank's to the gpiote's state.
but i have a error 8 invalid state whereas i had initialize
help me please !!! ...
I am using nordic nrf52840 sdk kit as a peripheral and mi 5A mobile as a central .The problem is continuously disconnecting with following reason
Reason: Remote User Terminated...
I am trying to read values from an analog peripheral device. To perform an analog read, I am using this example from the NordicSnippets simple examples:
https://github.com...
Hi, I have been trying this for 3 days.
I was using DBGX_EVTX in SR3v1.1 to check the log, it works fine and never goes wrong.
But in v1.2, is using another function instead...
Hello everybody,
I am using central device with SDK14.2 and S132.
In a central application, the operation sequence is as follows: * Buttons pressed and scan started *...
Reading analog signals while using the ble_peripheral_uart in SDK15.0.0 and sending strings to an iPhone
I am trying to read values from an analog peripheral device. To...
