Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hello,
I am truing to store data in the UICR register "customer area" from application code. The procedure is invoked only once when the registers are still empty. The...
Hello all,
In controlling two devices simultaneously from one central controller, I have noticed significant time delays in processing the second call to sd_ble_gattc_write...
Hi.
I am using PCA10028 board an SDK10.0.0.
nRF51's Max flash size is 256KB.
Q1. "s130_nrf51_1.0.0_softdevice.hex" size is 302KB already. How can we make HEX file less...
Hi.
I'm using PCA10028 and SDK10.0.0, S130 v1.0.0.
And "ble_app_hrs_c" example is my reference code.
It works well before i add code for timer as below.
void start_timer...
Hi I am an student who is a poor fledging embedded engineer.
I met an error on using nrfgo studio
when I click the tab [Device]-[nRF5X Programming]
I used JLink_V510p...
Hi,
Using ble-app-uart sdk9 example:
Is there a difference where I initialize uart in main? My code is able to run when I shifted the uart_init() after ble_stack_init...
Hi,
I am trying to figure out which GPIO pins i can use as UART on a nrf52 chip if i put it on a custom PCB (Not DK !!). From the reference manual (page 513, 48.10.7 and...
hi,
i want to restart my timer before it expires.
suppose my timeout is 2 second and i want to restart it in between 0-2 second based on signal when i receive before expires...
I've notice that the ST Balun NRF01D3 that I've used for my current design is not listed as compatible with Rev 3 (Build code: H) nRF51822 Silicon. Has there been any change...
Hi everyone,
I am looking into Crossworks and SEGGER's Embedded Studio and since they are related I am wondering which one of them is more recommendable? Right now Eclipse...
Hi,
I have set ble_adv_fast_timeout = 0 (same problem with ble_adv_slow_timeout) to get advertising forever, but when in call sd_ble_gap_adv_start, i get error 0x07 (param...
Hi all
According the nRF51822 Product Specification V3.1, the 16MHz RC oscillator has a tolerance of at most 5% and can be used as clock source for the UART module.
...
Hi,
I am trying to change an example code on ble_app_uart_c (Central) SDK10.0.0 s130.
I have changed already peripheral example and I can see notification data if I...
