I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
Hello,
I am using ble_app_multilink_central example as a foundation of my app involving central - peripherial connection (S120 - S110). My app works nicely but i have problem...
Hello, I am trying to establish a connection between the nRF52 board and the USB serial converter TTL-232R-3v3.
The setup is such that I connect the converter cable to...
Hi all,
we have a project based on nRF51422, SDK 6.1, Softdevice S310 2.0.1.
We use the bootloader for DFU services. Our problem is to send a service changed notification...
Dear all, I had debugged example Heart Rate Service from SDK 9.0.0 without problems but I think we have a exception, when I insert a breakpoint on line 923 instruction APP_ERROR_CHECK...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
We designed our own board using nRF8001 and EMF32, I used the EMF32 development kit to test the code and it is working fine. When I down the same code to my own board, it...
Hi ,
I am planning to implement S120 UART to communicate with desktop as well as S110 UART BLE.
I browsed in the forum and found out we already have example in github...
I have a small nRF51822 module that I want to use for UART communication without handshaking, and I'm having problems with reliability. Basically the nRF51822 crashes and...
Hi, I've got a pretty basic question, but I haven't found a satisfying answer for it. It is obvious, that the CC registers are 32 bit wide, but because the RTC Counter is...
Hello:
Does the nrf52 radio peripheral EasyDMA write to PACKETPTR on byte boundaries or does it write "bits"? Suppose I have the ADDRESS_BCSTART shortcut enabled and the...
Hi all,
I can use the API sd_ble_gap_rssi_start to start RSSI and can get the value when the BLE_GAP_EVT_RSSI_CHANGED event occurs.However,when I use the sd_ble_gap_rssi_stop...
Hi, I'm recently concerned with the latent risk that nrf51822 might be hacked by extracting the firmware also known as "snarf"ing.
And I know there is Memory Proection Unit...
I followed the guide of github.com/.../nRF51-ble-bcast-mesh to try the mesh with NRF51822.But there seem no discribtion about which softdevice we should use.I loaded the s110_nrf51822_7...
