Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hello,
Currently I am implementing the nrfx qdec driver in our Zephyr project using the nRF52840 DK. We choose the nrfx driver as this provides events. I am using the nRF...
Hi.
I have designed a node with NRF52833 with +8db power antenna.But i got some issue in signal transmission over 1km range.Please review my layout and matching circuit...
I have the software installed and I am using the nRF52840DK with Ubuntu 22.04. The uart link is /dev/ttyACM0
When I start wireshark and do a capture on all advertising channels...
Hello,
We are designing a product based on the RAK4630 module that integrates nRF52840 SoC.
Since we are creating a low power consumption and battery operated product...
I am trying to set up the AT library to directly talk to the modem through a uart on the nrf9160DK. But when I enter the commands to test "AT+CFUN?" I just get it echoed back...
I'm working with a Fanstel BT40 module which includes an nRF5340 and nRF21540 FEM. As a starting point I'm using the scan_adv example, which is working out-of-the-box but...
Hi,
I'm using Matter SDK v2.7.0, when I build example light_switch for Board: nrf7002dk_nrf5340_cpuapp with Configuration: prj.conf, I get errors as below:
/opt/nordic...
I have nrf9160 with w5500 ethernet module. I am successfully able to get IP address and connect to mqtt broker created locally on my network. Now I was trying to connect to...
Board: nrf7002 Project: matter_light_blub OS: Kubuntu 22 Toolchains: v2.7.0 SDK: v2.7.0
I have successfully deployed and tested projects that run normally, but when I...
Hi, Iam trying to run c++ code on nrf52840. I got working C code, so i try only change .c to .cpp. I got some errors but most of them are solvable by putting libraries(.h...
I was going through the driver files for CS47L63 and apparently I2C is not supported for some reason. Here is the code block I'm talking about
Is there any explicit reason...
I have successfully managed to incorporate the hard-float build of the library for the nrf52840 into my bare-metal application ( custom hardware with an nrf52840) and have...
LED5 is blinking very fast. no appearance on computer at all. nrfjprog --recover not reconvering, Tried another PC, another cable and no response at all.
I am trying to read the WHO AM I register of an ICM20948 over SPI with nRF52832, but I am getting incorrect values.
I have tried different SPI modes, but none of them work...
