We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
We are testing mass pairing on our windows machines, as we have seen problems with a high number of paired devices.
I am able to increment the mac address by using...
Hi,
A simple CMAKE question, somewhat regarding the zephyr build, but pretty essential for someone using JTAG to debug the application:
How does one disable optimization...
I need to make a reset of mesh device with clearing its configuration.
For this I tried to use model_config_file_clear() or mesh_stack_config_clear() functions.
However...
Hi,
How to enable fast mode for radio transmission and reception (I am using nRF5 SDK). These are the default examples and I can see that fast mode is not implemented: ...
Hello again,
I saw this Github 's post and I was wondering if is possible to use some of the libraries and drivers with nRF52811 and if so should I pay attention to some...
Hi,
Question:
In our project we need to drive some external components (High Side Drivers) via GPIO output.
In order switch on our “High Side Drivers” we need a voltage...
I'm using TWI and BLE functions together. My TWI sensor is operating at 400kHz, low priority. BLE has the highest priority. For example, if nRF52805 is sending commands to...
Hello community, I tried to read my motor encoders with the QDEC and capture the position of my motor. Hardware: nRF52840 DK, 2 Hal motor encoders on pin 0.13 and 0.14 which...
In NCS v1.6.99 the HEX data format is removed from data send and receive commands (socket, udp/tcp cli/srv), only ascii and data mode is supported.
In case of binary data...
Hello,
First time post and brand new to the nRF52832 chip. I am tasked with building firmware that will synchronize ADC samples across multiple devices. I have started with...
Hi to all team,
I have two units of nrf52840 dongle with me.
I have to develop the generic application firmware where data send from one dongle(coordinator) is getting...
Hi,
I have built ble board with nrf52832 with no pca10040 on my board and i have assign button switch pin as P.0.13 from nrf52832.Previously i am using nrf52832 dev kit...
Hello,
I have a custom example based on the "asset_tracker" application of the SDK v1.3.1 and I am trying to open the IDE through Toolchain Manager, but when I select "OPEN...
hi support team,
i was testing usb dfu(NCS1.6.0) function with window10, after i download the code, the windows seems not able to install the driver as below, and i couldn...
