Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
Is there an issue with my clock that's causing the BLE not to advertise? The debugger seems to an error on the gatt_params_init() function, which should mean its a RAM address...
Dear BLE mesh Experts, We want to provision and operate a mesh network using an app that is running on various phones. The idea is to use a single phone during installation...
hi Forum. I'm working on a project with nrf52840 + S140 + TWI (SDK v16). Got all working separatly on my custom board, i.e. softdevice alone works fine and TWI also works...
Hi,
I'm trying to implement Install Codes on our project without good results: The end device could not join the coordinator network after retrying several times.
Because...
Hi All,
I need to send HCI commands from my uC to nRF52840 (with DTM firmware) via UART to for example set channel, Tx power, packet type etc.
Are there any examples/documentation...
Hello,
nRF52832 BLE project using SDK 15.3.0 and SoftDevice 112 v6.1.1. Circuit has the output of a comparator connected to two GPIO pins (COMPARATOR_PIN1, COMPARATOR_PIN2...
Hey guys, I'm currently working with NRF9160, developing code that requires a work-item to be scheduled within a time-frame (timeout value) that could go up to >24-hrs. I...
Hello,
I am using nRF52840 S140 v7.0.1 and using ble_app_blinky. I have a query on Secure Serial DFU if there is a change in Flash and Ram address.
In original example...
Hello,
I am using nRF52840-pdk with Keil5 and nRF-go studio for development purpose.
I am facing an issue that after new firmware version upload from nRF-go studio to...
Hi everyone,
Currently, I was developing an application on top of Zephyr. I notice that NRF52 SDK provides library for MQTT-SN protocol. However, my application needs to...
Can the TCLK timeout be changed? I have a ZigBee device that joins and performs a key exchange but then is forced to leave the network 12 seconds later due to a TCLK timeout...
I am working on a project that I need to scan bluetooth devices. I am using nrf52832 as a central, sdk 15.2 and s132 v6.1.1. when I activate the advertiser tab on nrf connect...
Hi,
I haven't ran the FOTA download library in a while and I was just testing it. I don't seem to be getting any of the FOTA_DOWNLOAD_EVT events. I am running nRF SDK v1...
I am using nrf52832 as my cnetral and also nrf52832 as my peripheral . i am connected central with peeripheral using ble multilink example code. but it shows only 16bit uuid...
