Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hi all hope you all are fine and doing well.
I am trying to use the Soft UART (uart-bitbang.c driver) on nRF52 DK for a low-speed UART connection. The initialization fails...
NCS 3.4.0, sysbuild, with mcuboot enabled.
I want to use a simple custom "my.overlay" for both the app and mcuboot.
For the app it works with
-DEXTRA_DTC_OVERLAY_FILE...
I first noticed this when incorrect flags reported by mcumgr when performing network core update
When performing a network core update with CONFIG_SECURE_BOOT_APPCORE enabled...
Hello Nordic community,
using nrf5-sdk for nrf52840 SoC, I followed the uart example as below.
The uart tx and rx works fine BUT NOT THE HWFC
eg. When the CTS is set...
Hi Nordic Team,
Below are the configurations that I have done for the nRF21540 FEM.
.config file
#
# Multiprotocol service layer (MPSL)
#
# CONFIG_MPSL_FEM_ONLY is not...
I have a question regarding the solder balls on the WLCSP package of this device. Are they collapsing or non-collapsing? Can you also provide a definitive source for this...
I have been working on a soil moisture sensor for my indoor plants and I wanted to build some skills in PCB design using a Nordic SoC. I have chosen the nrf54L15 for this...
Hi,
I've got two ESB transceivers talking to each other - a PTX on nRF52832 (E73 module) and a PRX on nRF52810 (Holyiot module, the "tag"). Both chips can obviously TX and...
On a recent run of prototypes using the nRF9151 and the nPM1300 we've had a few failure where the nRF9151 cannot connect to the debugger and the board exhibits much higher...
I have two nRF9151 DK boards, both hardware revision 1.4.0, both showing the same SIM detection failure.
Symptoms on both boards:
AT%XSIM? always returns %XSIM: 0,9...
We have purchased a radio fitted with the nRF9160 modem and fitted it with a roaming SIM for NB-IoT use, we are in UK and have Band 20 EE and Vodafone.
What are the initial...
Now my product need FCC, and I use DTM example, only changed the txd,rxd pin in firmware, the lab can use nrfconnect for desktop to enter test, but the tx power is low when...
Dear Nordic,
I'm designing a 0.6mm thick 6-layer rigid-flex with the nRF54L15-CAAA, and due to my current stack-up the ground polygon to trace clearance can only go as small...
Hi Nordic Team,
Could you please clarify the SDK/NCS compatibility for the nRF54L15-CAAA chip?
We are planning to develop firmware in bare-metal mode and would like to...
