Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hello,
As per my understanding, SPP was supported by BT Classic and no more supported in BLE. I have a device, which runs SPP. It has to be connected to the BLE client....
Hi, I am now developing a product which uses nrf51422 chip. In this product, I use buttons to turn on and off (since I don't have hard-power cut off circuit, we use system...
Hi
I wonder if the SDK DTM example can be used with a Rhode & Schwarz CMW500 unit. Are the commands compatible with each other, i.e. expected by the CMW500 and DTM example...
Hi,
we're evaluating NRF52 as a platform for a project in the agricultural space and I have some beginner's questions:
Is it feasible to use a timer firing at 100kHz...
Hello,
I created a custom board with the BMD350 module (it has a nRF52832 chip), and I a trying to program it with the BMD300 eval board.
The module on my custom board...
I am using a nRF51422 device with the SDK 11. The task is to transmit battery service data to an application on the phone. I was wondering if there is a tutorial available...
Hi,
I used "ble_image_transfer" sample code and can get the all the stuff I want and now I'm implementing the central device for it,
but somehow I always got the "cccd_configure...
SDK 14.0.0/S132 5.0.0
When a whitelist is in use and during a connection, a call to ble_start_advertising is made to change advertising to a non-connectable type
since...
This keeps happening every time I stop the program for a while and then resume execution.
N.B. I did put a breakpoint trying to catch the problem.
Softdevice s132 6...
Hi All,
I have more boards on which I have loaded the code ble_app_uart_c (nRF5_SDK_15.2.0_9412b96) which I use as central devices and I have other boards on which I have...
I need to send the following sequence of bits through TWI
start bit | 7 bit address | write | slave ACK | stop bit
I looked through the twi_hw_master.c and it seems...
When building a project that compiles the hal_nfc_t2t.c, it errors for nRF52840, but works for nRF52832.
For the nRF52840, I get these errors:
Looking for some of the...
Hello, I want to transfer a large file (approx. 1.5MB) over BLE using nRF52 Module in a way where BLE Host and BLE Controller will be on the nRF52 SoC and the application...
I added ams service to my project, and I tested with my iphone 7P, seems all goes well. But today I tested with my iphone 5S, sometimes the hardfault exception raise.
