I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
Hi,
For 52820-QDAA, what load impedance is preferred seen into the matching network? I mean the total load impedance of C3, L1, C4, L2, RF trace and antenna.
Since our...
In our application, we've enabled full modem firmware update, which requires us to enable CONFIG_NORDIC_SECURITY_BACKEND. When we also enable memfault, this compile time pre...
I am build an application with features : When I not used nRF it imediately in sleep mode and be wake up by BLE events to send some text, and return to sleep mode ( the reson...
Hello there, Thanks for writing an application layer for SGTL5000. https://github.com/NordicPlayground/nRF52-teensy-sgtl5000-audio
I've configured the SGTL5000 to source...
We have a simple coin battery powered BLE device with a Laird BL652 module which has an nRF52832 chipset.
We have three buttons and set it up as low power as possible...
Hi, I downloaded a project from Git. I tried to open in SES using nRF Connect SDK. During the initial Cmake, the error occurs as shown in attached image.
Hello,
Our aim is to install "pc-ble-driver-js" and use the connectivity board for the serialization process.
We are following this link to get this working https://github...
Hi!
In previous versions of the SLM it was possible to provide a hex datatype to the XUDPSEND command to send blobs of data over UDP, without having to worry about a stray...
Hi,
I enable the watchdog in the application image, then call soft reset to enter the bootloader, the bootloader execution is also normal, until the watchdog is reset. ...
Hello!
I have a situation where a chip is connected with an antenna on a u.FL slot, what I want to do is to remove that antenna from the chip and connect my nrf52840 to...
Hi,
I want to send the I2S MIC Raw data through Ble by using ble_nus_send. I have written one application but it triggers a Cmake error. I have attached the log below...
HI I'm using the nrf5340dk, and I'm able to flash the application core with code that toggles the LEDs.
But I'm not able to flash the network core. I've specified in the...
Hi, I'm currently designing a system which requires Heart Rate monitorization and I'm using the MAX30101 chip to do so. I will be using I2C communication and, therefore, based...
1. We use code similar to the existing sample code to repeatedly sample a 0 - 2.25V voltage range using the SAADC. 2. Settings: 30s interval, single-ended input, burst-mode...
Hi All,
I'm looking for a PC based tool with similar functions as nRF connect. Our manufacturer is developing a functional test fixture which will PC based and will be...
