It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hello developers,
I saw the process of bluetooth scanning from nordic infocenter.
Scanning for advertisers performing legacy advertising
In this picture, I don't understand...
Hello,
I have an application that runs on a 9160 which uses mbedtls (via TFM) to connect to an AWS server. The application is using a CA that you folks have given me in...
Is there a way to change a build configuration after it was created?
I want to change the kconfig fragments it is calling, but I was no able too. I have to delete and create...
I am trying to test TLS communication between TCP server and client so, how I should generate the certificates and how to provision them in TCP server?
Can I use OpenSSL...
Hi, I am using nrf52832 development kit. MCU is waking up with two buttons and I put MCU to system off mode after successful data exchange or timeout. Init settings are like...
Hi,
I am configuring a button and an ISR to handle the events, but the interrupt is not called only when there is a transition.
Is there any other configuration needed...
During the End Of Line test of one of our device, based on nRF52832, we write the serial number of the device in some non volatile registers, specifically CUSTOMER[8] and...
Hello,
We are using the nRF52810-QCAA(QFN32) in a Beacon application. We have seen serious degradation in Radio performance while using the DC/DC vs. the LDO. More than...
Hi Forum,
i've ran into a problem with configure the nrf24l01. I've disabled all ShockBurst functionality (EN_AA = 0). When putting TX Payload into the Fifo the TX_EMPTY...
Hi~
We are going to use the MAC address and UUID as what we have.
I am trying to save the MAC address and UUID through UART, so I don't know what to do.
Currently the...
Hello,
I am trying to make a code running the Ble stack adn the FreeRtos one, i started from the project ble_app_hrs_freertos_pca10040_s132, i've just removed some things...
Hi.
Newbie stuck at installing IDE.
Trying to follow the automatic installation developer.nordicsemi.com/.../gs_assistant.html
Installed nRF Connect for Desktop v3.8...
Hi,
we have nrf52933 custom hardware.
we are flashing application through j-link.
but after every flashing , I need to hard reset the board in order to run the function...
Dear Nordic，
We developed a product based on the nRF52833 chip, with an external antenna, 3dBi gain. Set transmission parameters 100mS interval and 4dBm transmission power...
I have nrf52840 dongle will like to treat it as central. (like gateway) And sensor node is unknow ble, and adress type is Resolvable Private Address. If know the characteristics...
