Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
How can I do a point multiplication in NRF52840 using the ECC hardware accelerator for the secp256k1 curve? Also are there examples or any documentation on how to implement...
Hi,
I'm openning a new case (following the proposal of Einar Thorsrud ).
I want to do a BLE NUS project with custom service 128bits and with custom characteristics also...
Greetings!
Using the NRF52840 PDK, I succesfully erase, write and read without any modifications!
I have custom boards which involved a NRF52840 and a MX25R6435F (so same...
Dear Nordic Support,
My project is split into two parts: A firmware application that is based on the Generic Level Server model example (from the Mesh SDK) and an Android...
Good morning,
I'm working on nRF5 SDK v17.0.2 and I am using Segger Embedded Studios (SES) for the development.
I'm having a problem when I want to share my project...
I'm aware that the nRF CLI tools are not yet ported to AArch64 so they don't work natively on Apple Silicon. Normally rosetta 2 is fine, but nrfjprog is not compatible with...
working with nrf52832, sdk 16.0 s132 v7.01
in the uart example i get to this place in the code :
i get a pin toggle which makes my system do some unwanted things...
Hi,
I have a ARM based Linux host CPU connect to MDBT42Q-U(nRF52832).
But I cannot control it by BlueZ:
```
root@OpenWrt:/# btattach -B /dev/ttyMSM1 -P h4 & root...
Hello,
After some weeks of inactivity and moving my desk to an other address, the nRF connect application is not running and show a white screen for all applications except...
Just checking in, I am recently starting to develop cellular communication and looking to develop on the nRF9160. I have been in nRF52 space and with that I develop inside...
Hi, I'm using nrf52840 DK. In my project I want to receive audio from microphone (analog) and stream it to bluetooth headphones. Is there any possible way to do it? Any help...
Hi,
I have been working with a nRF52840 DK up until now, but I need to change and move to a nRF52833 DK. I wanted to adapt my code as they can both use the softdevice I...
Hi all
I'm working on a project based on the nRF52 chip and I'm encountering
If the system runs out of battery or no buttons are pressed within a timeout the system has...
Hello
I made an application on the nRF52 sdk, which works correctly.
Now I want to add the ability to update the firmware via OTA bluetooth.
I followed the instructions...
1. Using Zephyr, trying to config SPI_3 of nrf9160 more than 1MHz for flash interface.
2. Ending up in faults.
3. We need to configure SPI_3 as master with freq > 2MHz...
