We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm following this tutorial . In challenge 1, I was asked to change the transmit power level of the device.
Challenge 1: Try to add and populate the "p_tx_power_level...
Hi,
I am trying to integrate some ble code into my project but it keeps giving me errors like:
Error[Li005]: no definition for "ble_advertising_on_sys_evt" [referenced...
While developing code for our custom board, we ran into a filesystem corruption issue with fatfs+qspi block device and multiple directories. We were able to reproduce the...
I have problems running the ble_app_uart_pca1004e_s112 on a custom nrf52810 target devivce. The custom nrf52810 target is a custom board with the Rigado BMD 330, which is...
Hi there,
Please see the video for a full run down: https://www.youtube.com/watch?v=nIeIUMutBlU
Basically, I have a perfect and verified design that's been in the...
I'm using python code based on the heart_rate_collector.py example in pc-ble-driver-py to scan for devices and connect to a peripheral device.
This all works fine, except...
I have an existing Firmware (build on Crossworks) that has correct "floor" power consumption (< 10 uA during sd_app_evt_wait() on my setup).
I migrate my code to rune with...
I am stuck with strange behavior of s140 softdevice version 6.1.0 and later for ble_app_template example on nrf52840 preview dk(pca10056).
As I am planning to remove LF...
Hello,
We need to produce a driver for the ST25R3911B NFC chip working with NRF52840.
We just need to read NFCA tags so we thought that the example nfc/tag_reader included...
Hi i am using SDK15.2, nrf52832 board.
Which function is necessary to achieve multilink in example code. I dont understand how the central is connecting multiple peripherals...
I just purchased this unit and followed the setup instructions. I did not perform any flashing. When I plug the usb into the computer the jlink drive doesn't show up in Windows...
Hello, I am not sure if this was noted before. I didn't find anything about it. This is more of a suggestion. I was looking to use Thread CLI Example to use with the pca10059...
Hi,
I am using a custom board with the nrf52810 and trying to interface with the SHTW2 sensor. The sensor has an I2C interface and hence I use the TWI peripheral for this...
Hello,
I have a question regarding BLE_GAP_EVT_CONN_PARAM_UPDATE (nrf52840, SDK 15.2).
I'm evaluating the BLE_UART example using multiple peripherals. The goal is to scan...
