Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hello everyone!
I'm trying to implement a mqttsn client inside a microcontroller, and the nrf52840 should be used only as a way to communicate with other thread devices...
Hello!
My name is Tiago Morais. I've started to work with nrf52840 and now I'm having some problems with its CLI.
I'm trying to use the nrf52840 dk with openthread and...
Dear Nordic Team, Thanks for supporting.
Currently i am working with DFU for nRF52810 custom board. I am using SDK15.2.0. I followed these steps (//devzone.nordicsemi.com...
Hi all,
I'm following https://www.nordicsemi.com/DocLib/Content/SDK_Doc/Mesh_SDK/v3-0-0/md_doc_getting_started_dfu_quick_start and I'm using mesh SDK v3.0.0, I have a problem...
Hi all:
All of the example code is using GPIOTE to demonstrate how to handle GPIO interrupt.
However, it just can configured HiTOLow/LowToHi/Toggle.
If I want to trigger...
Works
Use nRF Connect v2.6.0 on Linux to erase, program softdevice.
Works
Use Keil to program application firmware
Does not work:
Use nRF Go studio to detect...
I need to implement a simple uart protocol. most messages are fixed length (8bytes) with some exceptions.
here what I do in pseudo code, I send 8bytes and expect 8bytes...
Hi
I am trying to port an SPI driver from a project for the NRF51822 to an NRF52832 and running into a problem reading more than two bytes. We are using SPI0 (not SPIM0...
Hello,
I'm using an NRF52 DK board.
I noticed that when I change P0.27 from the default (input / not connected to input buffer) to being an input pin connected to the...
Good evening,
I had a question in respect to the exact procedure needed to read a characteristic with read permissions. I have just discovered a service i would like to...
Board：PCA10056 （0.9.3）
SDK：15.2
Softdevice：S140
Example：ble_app_blinky
Today，I follow this page Using an ampere-meter for current measurement to measure the current...
Consider the following sequence of events:
1. `health_server_fault_register` is called, and it saves the current publish period.
2. Config server receives a message...
Building ‘Smart_Remote_3_nRF52_Firmware_nRF52832’ from solution ‘Smart_Remote_3_nRF52_Firmware_nRF52832’ in configuration ‘PCA20023-SR3_nRF52832_Product_Example’ Assembling...
Hi, Nordic,
I am using the ble_app_uart example in the SDK15.2.
I find a issue that when the device, which p_client->is_notification_enabled is already true, is disconnect...
Hi,
I just started with Nordic nRF52 DK and builded and flashed nRF5_SDK_15.2.0_9412b96/examples/ble_peripheral/ble_app_gls application on Ubuntu 18.04 using armgcc toolchain...
