I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
I have read the related issues, none of them provided a solution for me. There was one answer which suggested to downgraded libstdc++6 as a solution without giving any specific...
Recently, I have been working on integrating mcuboot with the partition manager from the NCS sdk. In addition, for another project, I am using Zephyr upstream and using Sysbuild...
I need to get the number of items stored in a fcb and there doesn't seem to be an easy way to get the count from the current read position (fcb_entry struct).
Can anyone...
Hi!
I use SDK15.0 and s132_nrf52_6.0.0_softdevice
I use nRF52 in two modes- peripherial and central in one time.
When I use it like peripherial and have connect with...
I am using RTT to debug my application and it's fine when it's working. The problem is that it seems to be flaky as hell. Sometimes it just stops working without any apparent...
I'm using the NCS 2.5.2 sdk and nrf 5340 with 7002, and I want to do BLE OTA DFU using external flash.
I've found this guide Add DFU support to your application - Software...
Hi,
I am learning my way with Zephyr on nrf5340 SoC, an loving it so far. Unfortunately I got stuck on something that should work out of the box, the setup of the BLS subsystem...
Hi
I want to use button interrupt in NCS.
There is no button interrupt enabled in initialization.
My test environment:ncs2.6.0,nRF52840DK.
In nRF5SDK, I only need...
Hello,
I am experienced working with Arduino and have developed projects with the XIAO BLE that has an nRF52 in built.
Right now I am developing a software using the nRF52...
Hi,
I try to install nrf connect SDK using the nrf extension in visual studio code.
I get error messages like :
[west]: fatal: unable to access ' github.com/....
I have developed the low-level drivers for the MT29F4G01ABAFDWB (using spi) NAND flash and am currently using the Zephyr RTOS. I would like to integrate FATFS into my NAND...
I'm still a beginner，I don't understand why the board I designed can't run the nRF connect SDK application, but the nRF5 SDK 17 application can run normally. I want to know...
Hi,
I have been using the nRF52840 Dongle for at least three months without any issues. First, I implemented my project on the nRF52840-DK, then easily configured it for...
Hello,
In my code, I would like to use the power_down_unused_ram () function. I included the ram_pwrdn.h file but the build returns with undefined reference to `power_down_unused_ram...
Hello. I want to the use pwm_library example for setting a PWM on a GPIO. It works well except that the initial state of the GPIO is high for about 230us before the PWM starts...
