I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hello,
I use Nrf52833DK running nRF Connect SDK (NCS)
I want read and write BLE MAC device address no matter it's the public one or static one.
Now i know bt_read_static_addr...
hello,
I'm try to fit my application to Android 14.
my application implement nordic DFU library ( for nrf52833 running freeRTOS firmware SDK 16 ) version 2.5.0
while...
Hi
I'm using the PDM module to capture audio through MP34DB02 PDM microphone ( here 's the datasheet). I set the clock frequency to default 1.032 MHz and a gain of +4 dB...
Hi there,
The nrf5340_audio application provides a -DFILE_ SUFFIX=fota overlay that adds FOTA capabilities to the application. This FOTA is introduced via Sysbuild configuration...
So I was experimenting with the Hardware Codec and I created a simple config which redirects the audio coming from the LINE IN mic to HEADPHONE OUT speakers.
Here's the...
We used the ADC nrf52832 to collect the reference source voltage, 1.240V. It is found that the consistency of each power-on is not good, for example, sometimes it is 2806...
Hi,
I'm running some transceiver tests to look at extended broadcast and ISO transfer modes. I am using nrf5340_audio_dk and ncs V2.6.0 to run nrf5340_audio application...
When testing the power consumption of the product with main IC 52832, we found that under the condition of 0dBm 1000ms, the peak current of beacon with PPK2 is about 15mA...
Hi, For the Adafruit Feather nRF52840 board I cannot find any information about the RTC. On the Feather board the 32kHz crystal is connected to the RTC clock input (P0.00...
Hi
I want to migrate my application to Zephyr RTOS platform from old setup given below.
Old Setup: Hardware: nRF52832 board. Soft device: S132 Software: SEGGER Embedded...
Hi, I'm new to Nordic Semiconductor chips.
I have experience programming STM32 and Atmel microprocessors. I would need to program/debug the NORDIC nRF52832 chip, without...
Hello there, I am working on enabling/ disabling DFU in nrf52840dk using ncs 2.4.2. previously i was doing it using ncs 1.8.0 as follows: libraries used:
#include <mgmt...
Hi,
I use the above function to create a new dataset. When I use SDK 2.3.0, this works perfectly. But when I use SDK 2.6.0 I get the following.
When I tried
arm-zephyr...
Hi all!
So I'm just starting out with the Thingy 91 and I was following the Nordic Thingy 91: Getting Starting Guide and I was in the process of using MCUBoot to update...
